Abstract:With increasing diameters of aluminum alloy thin-walled tubes (AATTs), the tube forming limits, i.e. the minimum bending factors, and their predictions under multi-index constraints including wrinkling, thinning and flattening have been being a key problem to be urgently solved for improving tube forming potential in numerical control (NC) bending processes of AATTs with large diameters. Thus in this paper, a search algorithm of the forming limits is put forward based on a 3D elastic-plastic finite element (FE) model and a wrinkling energy prediction model for the bending processes under axial compression loading (ACL) or not. This algorithm enables to be considered the effects of process parameter combinations including die, friction parameters on the multi-indices. Based on this algorithm, the forming limits of the different size tubes are obtained, and the roles of the process parameter combinations in enabling the limit bending processes are also revealed. The followings are found: the first, within the appropriate ranges of friction and clearances between the different dies and the tubes enabling the bending processes with smaller bending factors, the ACL enables the tube limit bending processes after a decrease of the mandrel ball thickness and diameters; then, without considering the effects of the tube geometry sizes on the tube constitutive equations, the forming limits will be decided by the limit thinning values for the tubes with diameters smaller than 80 mm, while the wrinkling for the tubes with diameters no less than 80 mm. The forming limits obtained from this algorithm are smaller than the analytical results, and reduced by 57.39%; the last, the roles of the process parameter combinations in enabling the limit bending processes are verified by experimental results.

Wrinkling Limit Based on Fem Virtual Experiment During Nc Bending Process of Thin-Walled Tube

A New Method to Accurately Obtain Wrinkling Limit Diagram in Nc Bending Process of Thin-Walled Tube with Large Diameter under Different Loading Paths

Wrinkling Analysis for Forming Limit of Tube Bending Processes

Influences of Forming Parameters on Wrinkling in NC Thin-walled Tube Bending

A Study on Plastic Wrinkling in Thin-Walled Tube Bending Via an Energy-Based Wrinkling Prediction Model

The Interactive Effects of Wrinkling and Other Defects in Thin-Walled Tube NC Bending Process

Forming Characteristics of Thin-Walled Tube Bending Process with Small Bending Radius

3D Numerical Study on Wrinkling Characteristics in NC Bending of Aluminum Alloy Thin-Walled Tubes with Large Diameters under Multi-Die Constraints

Predicting the wrinkling in AA5052 seamless tubes manufactured by free bending forming technology

Effect of Clearance on Wrinkling of Thin-Walled Rectangular Tube in Rotary Draw Bending Process

Forming Limits under Multi-Index Constraints in NC Bending of Aluminum Alloy Thin-Walled Tubes with Large Diameters

Explicit Fe Wrinkling Simulation and Method to Catch Critical Bifurcation Point in Tube Bending Process

Experimental Study of the Influence of Processing Parameters on Forming Quality of Thin-Walled NC Bending Tube

Modelling of Wrinkling in NC Bending of Thin-walled Tubes with Large Diameters under Multi-die Constraints Using Hybrid Method

Study on Wrinkling Behavior in Hydroforming of Large Diameter Thin-Walled Tube Through Local Constraints

Simulation and the Experimental Analysis on Wrinkling at Flat Tube Rotary Bending In-Plane

Forming Characteristics of Al-alloy Large-diameter Thin-walled Tubes in NC-bending under Axial Compressive Loads

Multiple Instability-Constrained Tube Bending Limits

An Imperfection-Based Perturbation Method for Plastic Wrinkling Prediction in Tube Bending under Multi-Die Constraints

Numerical Study on Deformation Behaviors of Thin-Walled Tube NC Bending with Large Diameter and Small Bending Radius

Study on Significant Influence of Process Parameters on Wrinkling of Rotary-draw Bending Formation of Thin Walled Rectangular Tube