Abstract:In recent publications, we have shown that repeated bending and unbending during tension can significantly increase the percent elongation-to-fracture (ETF) of metallic sheets. A custom-built machine for cyclic bending under tension (CBT) testing was designed and used to test several sheet metals. In particular, the improvements in ETF using CBT were over 3× relative to simple tension (ST) for commercially pure titanium (cp-Ti) sheets. The present paper evaluates the influence of specimen width on the achieved ETF in CBT of cp-Ti sheets. To facilitate the study, the CBT machine was furnished with wide grips to enable processing of sheets in addition to testing narrow strips. The ETF was observed to reduce with the sheet width. To rationalize the observations, the strain rate-independent plasticity theory of von Mises ( J 2 ) with isotropic expansion of yield surfaces of cp-Ti was used in finite elements (FE) to perform a set of simulations. To facilitate the FE simulations of the CBT process stretching the sheets of cp-Ti far beyond the point of maximum uniform strain in ST, the post-necking hardening behavior was inferred along RD, TD, and 45 sheet directions using an established methodology combining ST tests, CBT tests, and modeling material behavior during CBT. Simulated geometries and mechanical fields were found to be in good agreement with corresponding measurements for every specimen width. While predicted axial strains were similar for every width, the strain path shifted from uniaxial tension for the narrow specimen toward plane-strain tension for the wider specimens. As such, as plane-strain tension was approached via progressively wider specimens, the width strain was reduced, while the thinning strains increased. The increase in the thinning strain was established as the primary reason for the reduced ETF with increasing sheet width. Experimental and FE simulation results along with the insights into the influence of specimen width on the ETF in CBT of cp-Ti are presented and discussed.

Formability of Thin-Walled Commercial Pure Titanium Tube upon Rotary Draw Bending

Experimental and Numerical Studies on the Formability of TB5 Titanium Sheet in Rubber Cold Forming

Research on Bending Forming Method of Large Diameter-Thickness Ratio Thin-Walled Tubes for Aerospace

Forming characteristics of thin-walled tubes manufactured by free bending process-based nontangential rotation bending die

Bending forming of lightweight large diameter thin-walled aluminum alloy aviation tube

Formability Enhancement in Titanium Tube-Flaring by Manipulating the Deformation Path

Hot Gas Pressure Forming of Ti-55 High Temperature Titanium Alloy Tubular Component

Springback Analysis for Warm Bending of Titanium Tube Based on Coupled Thermal-Mechanical Simulation

An Experimental and Simulation Study on the Formability of Commercial Pure Titanium Foil

Deformation Patterns in Hydroforming of Thin-Walled Y-Shaped Tube

Numerical Modeling and Experimental Study of Microstamping Process for Fabricating Microchannels Using Thin Sheets of Titanium

Hot Gas Pressure Forming and Post Aging Treatment of Ti-22Al-24.5Nb-0.5Mo Square Tubes

3D free thermal bending of BR1500HS high-strength steel tube: Simulation and experimental investigation

Influence of mechanical properties of tube on forming limits and deformation characteristics in expansion drawing process

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Investigation on the influence of mandrel on the forming quality of thin-walled tube during free bending process

Influence of specimen width on the elongation-to-fracture in cyclic-bending-under-tension of commercially pure titanium sheets

Formability and microstructure of TC4 titanium alloy hollow shafts formed by cross-wedge rolling with a mandrel

Uncertainty analysis and robust design optimization for the heat-assisted bending of high-strength titanium tube

Analysis of Bending Deformation and Stress of 6063-T5 Aluminum Alloy Multi-Cavity Tube Filled with Liquid

Process Development for a Superplastic Hot Tube Gas Forming Process of Titanium (Ti-3Al-2.5V) Hollow Profiles