Abstract:Typically, due to their limited formability, elevated temperatures are required in order to achieve complex shapes in titanium alloys. However, there are opportunities for forming such alloys at room temperature using incremental forming processes such as single-point incremental forming (SPIF). SPIF is an innovative metal forming technology which uses a single tool to form sheet parts in place of dedicated dies. SPIFs ability to increase the forming limits of difficult-to-form materials offers an alternative to high temperature processing of titanium. However, sheet thinning during SPIF may encourage the early onset of fracture, compromising in-service performance. An additive step prior to SPIF has been examined to tailor the initial sheet thickness to achieve a homogeneous thickness distribution in the final part. In the present research, laser metal deposition (LMD) was used to locally thicken a commercially pure titanium grade 2 (CP-Ti50A) sheet. Tensile testing was used to examine the mechanical behaviour of the tailored material. In addition, in-situ digital image correlation was used to measure the strain distribution across the surface of the tailored material. The work found that following deposition, isotropic mechanical properties were obtained within the sheet plane in contrast to the anisotropic properties of the as-received material and build height appeared to have little influence on strength. Microstructural analysis showed a change to the material in response to the LMD added thickness, with a heat affected zone (HAZ) at the interface between the added LMD layer and non-transformed substrate material. Grain growth and intragranular misorientation in the added LMD material was observed. SPIF of a LMD tailored preform resulted in improved thickness homogeneity across the formed part, with the downside of early fracture in a high wall angle section of the sheet.

An Experimental and Simulation Study on the Formability of Commercial Pure Titanium Foil

Experimental and Numerical Studies on the Formability of TB5 Titanium Sheet in Rubber Cold Forming

Identification of Forming Limits of CP Titanium Gr 2 Using Electrically Assisted Warm ISF Process

Tailoring Titanium Sheet Metal Using Laser Metal Deposition to Improve Room Temperature Single-Point Incremental Forming

Effect of forming temperature and fiber orientation on the warm deep drawing formability of TA2/Cf/PEEK laminates

Formability of Thin-Walled Commercial Pure Titanium Tube upon Rotary Draw Bending

Hot Gas Pressure Forming of Ti-55 High Temperature Titanium Alloy Tubular Component

Numerical Modeling and Experimental Study of Microstamping Process for Fabricating Microchannels Using Thin Sheets of Titanium

Formability of Ultrasonically Additive Manufactured Ti-Al Thin Foil Laminates

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Hybrid forming process combining electromagnetic and quasi-static forming of ultra-thin titanium sheets: Formability and mechanism

Characterization and Formability of Titanium/Aluminum Laminate Composites Fabricated by Hot Pressing

Advanced FEM Insights into Pressure-Assisted Warm Single-Point Incremental Forming of Ti-6Al-4V Titanium Alloy Sheet Metal

An Experimental Study on the Frictional Behavior of Ultrathin Metal Sheets at Elevated Temperatures

Thermo-Mechanical Numerical Simulation of Friction Stir Rotation-Assisted Single Point Incremental Forming of Commercially Pure Titanium Sheets

Formability and microstructure of TC4 titanium alloy hollow shafts formed by cross-wedge rolling with a mandrel

Microstructure and Mechanical Property Characterizations of Metal Foil after Microscale Laser Dynamic Forming

Forming Analysis and Heat Treatment of TC31 Titanium Alloy Component with High Ribs and Thin Webs

Research on the thermal forming limit diagram (TFLD) with the M-K model for Ti-6Al-4V alloy

Forming limit diagrams and mechanical properties of AA1050/Ti CP2 multilayered composite produced by the accumulative roll bonding technique

Investigation on mechanism in fabricating truncated cone with tooth features of titanium alloy via flexible free incremental forming at room temperature