Abstract:In the present work, (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 were produced by common casting and hot-forging technology utilizing the SHS reactions between titanium and B4C, C powder. The microstructures of composites were examined using optical microscopy (OM) and transmission electron microscopy (TEM). The X-ray diffraction (XRD) was used to identify the phases that were present in the composites. There are three phases — TiB, TiC and titanium matrix alloy. TiB grows in short-fiber shape, whereas TiC grows in dendritic, equiaxed or near-equiaxed shape. TiB whiskers were made to align the longitudinal direction and TiC dendritic was broken up after hot-forging. The reinforcements are distributed uniformly in matrix alloy. The interfaces between reinforcements and titanium matrix alloy are very clean. The tensile strength (yield strength and ultimate tensile strength) and the Young's modulus improve with the addition of TiB whiskers and TiC particles although some reduction in ductility is observed. (TiBw+TiCp)/Ti6242 composites with TiB:TiC=4:1 will fracture on a lower level of applied stain due to deformation restraint of TiB whiskers on titanium matrix alloy. The (TiBw+TiCp)/Ti6242 composites with TiB:TiC=1:1 show higher tensile strength and ductility. The addition of graphite not only improves the tensile strength and the Young's modulus but also increases the ductility. The improved Young's moduli and increased tensile strengths of the composites are explained using shear lag and rule-of mixtures theories. The Young's moduli of the composites were found in good agreement with that calculated from Tsai–Halpin equation applied for discontinuous-reinforced composites.

Study on mechanical properties of C-f/TiC-TiB2 composites combustion-synthesized by SHS

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

In situ synthesis and mechanical properties of bulk Ti3SiC2/TiC composites by SHS/PHIP

PROPERTIES OF TiC-Al2O3/Fe COMPOSITES PREPARED BY SHS/PHIP

The influences of cu content on the self-propagating high temperature synthesized TiC-TiB2 composites

Strengthening and toughening of Ti 5 Si 3 by TiC-coated short carbon fiber: Fabrication, interfacial control, and mechanism of reinforcement

Strengthening and toughening of TiC ceramics by short carbon fibers

MECHANICAL PROPERTIES OF TiC-Ni PRODUCED BY SHS AT ROOM AND HIGH TEMPERATURES

The Influence of TiC Content on The Properties of Tungsten Matrix Composites

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC

Self-propagating high-temperature synthesis of TiC-TiB2/Cu ceramic-matrix composite

Mechanical Properties and Strengthening Effects of in Situ (Tib+tic)/ti-1100 Composite at Elevated Temperatures

Self-propagating high temperature combustion synthesis of TiB/Ti composites

Microstructure and mechanical properties of TiB2-40 wt% TiC composites: Effects of adding a low-temperature hold prior to sintering at high temperatures

Effect of TiC content on the microstructure and mechanical properties of Ti-30Mo-xTiC composites

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

The fabrication and mechanical properties of Ti3SiC2/HAp ceramics composites

Mechanical Properties and Strengthening Mechanisms of in Situ (Tib+tic)/ti-1100 Composite at Elevated Temperature

Enhancement mechanical properties of in-situ preparated B4C-based composites with small amount of (Ti3SiC2+Si)

In-situ TiC/Ti composites based on Ti 2 AlC–Ti system: Reaction process, microstructure, and mechanical properties

Microstructure and Tensile Properties of in Situ (tib+tic)/ti6242 (tib:Tic=1:1) Composites Prepared by Common Casting Technique