Abstract:The process of preparing SiC fiber-reinforced γ -TiAl composites by the conventional methods is difficult and complicated due to the high reactivity, high melting point and poor deformability of γ -TiAl alloys. In this work, suction casting, a promising method for preparing SiC f /TiAl composite, had been attempted. In the process, γ -TiAl alloy melt was introduced rapidly into a mold within pre-arranged fibers that were coated with additional layer of titanium alloy. This simple method successfully prevented serious reactions between the alloy melt and the fibers which remained intact during the solidification process. The interfacial reaction layer was observed by optical microscopy, scanning electron microscopy (SEM). The interfacial reaction products were identified by transmission electron microscopy (TEM). Tensile tests of the matrix alloy and composites were performed at room temperature and 800 °C. The results exhibited that the tensile strength of SiC f / γ -TiAl composite was higher than that of the matrix alloy at both room temperature and 800 °C. At room temperature, tensile strength of SiC f / γ -TiAl composite was increased by about 7% (50 MPa), whereas a double increase in tensile strength 14% (100 MPa) was obtained at 800 °C. The titanium alloy coating on the fiber not only prevented the serious interfacial reaction between the γ -TiAl alloy melt and the SiC fiber, but also played a role in delaying the propagation of cracks in the matrix to the fiber at 800 °C. The fracture mechanism of the composite was analyzed by fracture metallographic analysis.

Strengthening and toughening of Ti 5 Si 3 by TiC-coated short carbon fiber: Fabrication, interfacial control, and mechanism of reinforcement

Spark plasma sintering of TiC-based composites toughened by submicron SiC particles

Strengthening and toughening of laminated TiAl composite sheets by titanium alloy layers and carbide particles

Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

The Flexural Strength and Fracture Toughness of TC4-Based Laminated Composites Reinforced with Ti Aluminide and Carbide

Preparation and toughness mechanism of in-situ Ti3AlC2 enhanced and toughened TiAl3 matrix composites

Tensile Behavior of SiC Fiber-Reinforced Γ -Tial Composites Prepared by Suction Casting

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

Enhanced properties of titanium matrix composites via in-situ synthesized TiCx and Ti 5 Si 3 with network structure

Microstructure and mechanical behaviour of transient liquid phase spark plasma sintered B4C–SiC–TiB2 composites from a B4C–TiSi2 system

Fabrication of dense Cf/SiC ceramic matrix composites using 3D printing and PIP with short carbon fibre as a toughening material

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Microstructure, mechanical properties and strengthening mechanism of in-situ synthesized TiC/6061 nanocomposites

High-performance Ti composites reinforced with in-situ TiC derived from pyrolysis of polycarbosilane

Effect of TiC content on the microstructure and mechanical properties of Ti-30Mo-xTiC composites

Densification, Microstructure and Mechanical Performance of TiC/Fe Composites by Spark Plasma Sintering

Effectively enhanced strength by interfacial reactions in in-situ carbon reinforced Al matrix composites

Tailoring Ultrafine Grained and Dispersion-Strengthened Ti2AlC/TiAl Composite Via a New Fabrication Route