Abstract:There is great economic incentive in developing efficient catalysts to produce hydrogen or syngas by catalytic partial oxidation of methane (CPOM) since this is a much less energy-intensive reaction than the highly endothermic methane steam reforming reaction, which is the prominent reaction in industry. Herein, we report the catalytic behavior of nickel-based catalysts supported on different oxide substrates (Al2O3, CeO2, La2O3, MgO, and ZrO2) synthesized via wet impregnation and solid-state reaction. Furthermore, the impact of Rh doping was investigated. The catalysts have been characterized by X-ray diffraction, N2 adsorptiondesorption at -196°C, temperature-programmed reduction, X-ray photoelectron spectroscopy, O2-pulse chemisorption, transmission electron microscopy, and Raman spectroscopy. Supported Ni catalysts were found to be active for CPOM but can suffer from fast deactivation caused by the formation of carbon deposits as well as via the sintering of Ni nanoparticles (NPs). It has been found that the presence of Rh favors nickel reduction, which leads to an increase in the methane conversion and yield. For both synthesis methods, the catalysts supported on alumina and ceria show the best performance. This could be explained by the higher surface area of the Ni NPs on the alumina surface and presence of oxygen vacancies in the CeO2 lattice, which favor the proportion of oxygen adsorbed on defect sites. The catalysts supported on MgO suffer quick deactivation due to formation of a NiO/MgO solid solution, which is not reducible under the reaction conditions. The low level of carbon formation over the catalysts supported on La2O3 is ascribed to the very high dispersion of the nickel NPs and to the formation of lanthanum oxycarbonate, through which carbon deposits are gasified. The catalytic behavior for catalysts with ZrO2 as support depends on the synthesis method; however, in both cases, the catalysts undergo deactivation by carbon deposits.

Partial Oxidation of Methane to Syngas over Cr2o3 Catalysts

Investigation on the Performance of Supported Molybdenum Carbide for the Partial Oxidation of Methane

Catalytic partial oxidation of methane over rhodium coated foam monolith

Partial Oxidation of Methane over CaO Decorated TiO2 Nanocatalyst for Syngas Production in a Fixed Bed Reactor

Studies on the Performance and Structure of Supported Catalysts for the Partial Oxidation of Methane to Syngas

The performance of methane aromatization on Mo-Cr/HZSM-5 catalyst

Promoted Ni Catalyst Over Titania-Zirconia Support for Partial Oxidation of Methane: Simple and Practical Catalysts

Effect of Ni Loading and Reaction Conditions on Partial Oxidation of Methane to Syngas

Partial oxidation of methane to syngas over Ni/Al2O3 catalysts prepared by a modified sol-gel method

Partial Oxidation of Methane to Syngas in Tubular Oxygenper-Meable Reactor

Simulation of Partial Oxidation of Methane on the Rhodium Coated Foam Monolith Based on the Elementary Kinetics

Catalyst Deactivation of Rh-Coated Foam Monolith for Catalytic Partial Oxidation of Methane

Atomically dispersed MoNi alloy catalyst for partial oxidation of methane

Partial Oxidation of Bio-methane over Nickel Supported on MgO-ZrO2 Solid Solutions

Partial oxidation of methane in hollow‐fiber membrane reactors based on alkaline‐earth metal‐free CO2‐tolerant oxide

Experimental Study and Modeling Analysis of Catalytic Partial Oxidation of Methane with Addition of Co2 and H2o Using A Rh-Coated Foam Monolith Reactor

Properties of Ni/Y2O3 and Its Catalytic Performance in Methane Conversion to Syngas

Partial Oxidation of Methane to Syngas Over Nickel-Based Catalysts: Influence of Support Type, Addition of Rhodium, and Preparation Method

Oxidative Coupling of Methane over Pt/Al2O3 at High Temperature: Multiscale Modeling of the Catalytic Monolith

Combined Single-pass Conversion of Methane Via Oxidative Coupling and Dehydro-aromatization

Active site for syngas production by direct partial oxidation of CH 4 over ZrO 2