Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

Thermal Stability and Electrode Properties of Melt-Spun Mg65cu25nd10 Amorphous Alloy

Nanocrystallization and hydriding properties of amorphous melt-spun Mg65Cu25Nd10 alloy

Microstructural Investigation and Electrochemical Property of Mg63Ni27Nd10 Amorphous Alloy

Electrode properties of melt-spun Mg–Ni–Nd amorphous alloys

The phase structure and electrochemical properties of the melt-spun alloy Zr0.7Ti0.3Mn0.4V0.4Ni1.2

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

Crystallization Kinetics of Mg65Cu25Nd10 Amorphous Alloy

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

Properties of Amorphous Mg 65 Ni 10 RE 25 (re=la, Ce, Pr, Nd, Mm) Hydrogen Storage Alloys Electrode

Microstructural Transformation And Electrochemical Properties Of Mg-Ni-Y-La Amorphous Alloy

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

Structure and mechanical properties of Mg85Cu5Zn5Y5 amorphous alloy containing nanoscale particles

A Discussion on Decay of Discharge Capacity for Amorphous Mg–Ni–Nd Hydrogen Storage Alloy

The Relation Between the Discharge Capacity and Cycling Number of Mechanically Alloyed MgxNi100−x Amorphous Electrode Alloys

Influence of Annealing Treatment on Microstructure and Cycling Stability of La-Rich Ml(Nicomnal)(5) Alloy Electrode for Ni/Mh Batteries

Microstructural Investigation of Electrochemical Hydrogen Storage in Amorphous Mg–Ni–La Alloy

Preparation and Discharge Properties of Amorphous Mg_(65-x)Ni_(21)Pr_(14) Agx Alloy Electrodes

Crystallization Microstructure of Mg65Cu25Y10 Bulk Amorphous Alloy

Preparations and Electrochemical Properties of Amorphous Ti-Al Alloys