Abstract:The formation of polymeric micro-patterns on various substrates via a photolithography procedure has been widely used in semiconductor fabrication. Standard polymer patterns are usually fabricated via photosensitive polymer varnishes, in which large amounts of potentially harmful solvents with weight ratios over 50 wt% have to be removed. In the current work, a novel pattern-formation methodology via solvent-free electrospun photosensitive polymeric fibrous membranes (NFMs) instead of the conventional photosensitive solutions as the starting photoresists was proposed and practiced. For this purpose, a series of preimidized negative auto-photosensitive polyimide (PSPI) resins were first prepared via the two-step chemical imidization procedure from the copolymerization reactions of 3,3′,4,4′-benzophenonetetracarboxylic- dianhydride (BTDA) and two ortho-methyl-substituted aromatic diamines, including 3,3′,5,5′-tetramethyl-4,4′-diaminodiphenylmethane (TMMDA) and 3,7-diamino-2,8-dimethyl- dibenzothiophene sulfone (TSN). The derived homopolymer PI-1 (BTDA-TMMDA) and the copolymers, including SPI-2~SPI-6, with the molar ratio of 5~25% for TSN in the diamine units, showed good solubility in polar solvents. Then, a series of PSPI NFMs were fabricated via standard electrospinning procedure with the developed PSPI solutions in N,N-dimethylacetamide (DMAc) with a solid content of 25 wt% as the starting materials. The derived PSPI NFMs showed good thermal stability with 5% weight loss temperatures higher than 500 °C in nitrogen. Meanwhile, the derived PSPIs showed good photosensitivity to the ultraviolet (UV) emitting wavelengths of i-line (365 nm), g-line (405 nm) and h-line (436 nm) of the high-pressure mercury lamps in both forms of transparent films and opaque NFMs. Fine micro-patterns with a line width of around 100 μm were directly obtained from the representative SPI-4 NFM via standard photolithography procedure.

Ultrafine Pattern X-Ray Mask Fabricated Using the Sidewall Method

Fabrication of Ultra-Thick Masks for X-ray Phase Contrast Imaging at Higher Energy

Fabrication of 11-Nm-wide Silica-Like Lines Using X-Ray Diffraction Exposure

Implementation of high‐performance, freestanding flexible film masks through photosensitive polyimide for arbitrary surface micropatterns creation

X-Ray Lithography Technology for the Fabrication of Deep-Submicron T-Shaped Gate

Flexible, Reusable and Ultra-Thin Parylene-C/Cr Shadow Mask for Versatile Micropatterning Applications on Planar and Nonplanar Surfaces

Fabrication of X-ray mask by using diamond membrane

The Design, Fabrication and Performance of A Large Area 10000 Line/Mm Metal Transmission Diffraction Gratings for Soft X-Ray

Highly efficient and controllable method to fabricate ultrafine metallic nanostructures

Ultrathin Resist Films Patterning Using a Synchrotron Radiation Lithography System

A Novel Pmma/Neb Bilayer Process for Sub-20 Nm Gold Nanoslits by A Selective Electron Beam Lithography and Dry Etch

Reusable, Flexible, and Low Cost Parylene-C/cr Shadow Mask for Micropatterning on Arbitrary Surfaces

Reflective X-ray masks for X-ray lithography

Progress in the fabrication of low-defect density mask blanks for extreme ultraviolet lithography

A Simple Photomask with Photoresist Mask Layer for Ultraviolet-Photolithography and Its Application for Selectively Photochemical Surface Modification of Polymers

Formation of Nano-Fibrous Patterns on Aluminum Substrates via Photolithographic Fabrication of Electrospun Photosensitive Polyimide Fibrous Membranes

Nanoscale-Patterned Cr Films by Selective Etching Using a Heat-Mode Resist: Implications for X-ray Beam Splitter

Development of a facile block copolymer method for creating hard mask patterns integrated into semiconductor manufacturing

Maskless Nanostructure Photolithography by Ultrahigh-Order Modes of a Symmetrical Metal-Cladding Waveguide

New type of X-ray mask based on mica substrate

Rapid Nanofabrication with High Density Pattern with UVN30 Chemically Amplified Resist