Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Effects of Single-walled Carbon Nanotubes with Ni Layers on Microstructure of Magnesium-matrix Composites

Strengthening Ni-Coated CNT/Mg Composites by Optimizing the CNT Content

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Effect of carbon nanotubes grown temperature on the fracture behavior of carbon fiber reinforced magnesium matrix composites: Interlaminar shear strength and tensile strength

Microstructure and Mechanical Properties of ABOw and Nickel-Coated MWCNTs Reinforced 2024al Hybrid Composite Fabricated by Squeeze Casting

Study on Properties of Carbon Nanotube/Magnesium Matrix Composite

Properties of Carbon Nano-tubes/Magnesiuum Matrix Composite by Casting

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

The effect of carbon nanotubes microstructures on reinforcing properties of SWNTs/alumina composite

Microstructure, Interface and Strengthening Mechanism of Ni-CNTs/AZ91 Magnesium Matrix Composites

Design and Preparation of CNTs/Mg Layered Composites

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Effect of carbon nanotube content and annealing temperature on corrosion performance of carbon nanotube/Ni composite layer

Preparation of Structure-Function Integrated Layered CNT/Mg Composites

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes

Study on the Mechanism of CNTs Regulating the Microstructures and Properties of Al–Cu–Mg Alloy

Effects of the addition of Ni-plated carbon nanotube on the microstructure and properties of injection molded FeAl

On the role of carbon nanotubes addition in carbon fiber-reinforced magnesium matrix composites

Microstructure and compressive properties of Mg–9Al composite reinforced with Ni-coated graphene nanosheets

Microstructure, Mechanical and Wear Properties of Short Carbon Fiber-Reinforced AM50 Magnesium Matrix Composite

Fabrication and characterization of CNT-reinforced Ni-Co composite coatings: microstructural evolutions and corrosion behavior