Abstract:This study examines the mechanical properties and wear mechanisms of magnesium (Mg) metal matrix composites reinforced with titanium (Ti) and silicon carbide (SiC) particles. Three different composite formulations were investigated: Mg-30 wt% Ti (A), Mg-25 wt% Ti-5 wt.% SiC (NB), Mg-20 wt% Ti-10 wt% SiC (NC), and Mg-15 wt% Ti-15 wt% SiC (ND). These composites were fabricated through ball milling and spark plasma sintering (SPS). The incorporation of SiC particles significantly enhanced grain refinement and phase formation within the composites. Density analysis revealed that the actual densities of the composites were lower than the theoretical values, with Composite A exhibiting the highest actual density of 2.15 g/cm3 and the lowest porosity of 16.31%. The introduction of SiC particles increased porosity, with Composite NB displaying the highest porosity at 30.58%. Hardness testing indicated that Composite NC, containing 10 wt% SiC, achieved the highest hardness of 137 HV. In contrast, Composite ND, with 15 wt% SiC, showed a reduced hardness of 115 HV, attributed to increased porosity and potential SiC particle agglomeration. Wear behavior was evaluated using a pin-on-disc tribometer. Weight loss measurements indicated that Composite A had the lowest weight loss (1.1–2.1 mg), while Composite NB experienced the highest weight loss (2.8–8.3 mg) due to increased porosity. Composite NC demonstrated a balance with moderate weight loss (2.0–3.8 mg). The coefficient of friction (COF) varied with SiC content and applied loads (2, 4, and 8 N), with Composite A demonstrating the lowest COF values (2.3–2.8) and stable performance across different loads. Composite NB exhibited higher COF values (3.5–4) and significant fluctuations due to elevated porosity and the presence of SiC particles. Composite NC showed better wear resistance and more stable COF values (2.5–2.9) compared to NB and ND.

Microstructure, Mechanical and Wear Properties of Short Carbon Fiber-Reinforced AM50 Magnesium Matrix Composite

Microstructure, mechanical properties and thermal conductivity of the short carbon fiber reinforced magnesium matrix composites

Micro-structural and tensile strength analyses on the magnesium matrix composites reinforced with coated carbon fiber

Fabrication of Ni-coated carbon nanotubes reinforced magnesium matrix composites

Mechanical Properties, Aging Behavior and Microstructure Evolution of Mg-Nd-Zn-Zr Based Magnesium Matrix Composite Reinforced with Alumina Fibers

Influence of Carbon on the Wear Resistance, Strength, and Hardness of Composites with a Fe−Cr–Mn–Mo–N–C Matrix

Fabrication and Properties of Magnesium Matrix Composite Reinforced by Carbon Nanotubes-Alumina Hybrid Reinforcements

Microstructure, Mechanical Properties and Wear Resistance of As-Cast Mg-3Al-1Ca-0.4Mn/Tip Magnesium Matrix Composites

Interfacial Modification Using Matrix Alloying in Mg/CNT Composites for Improved Mechanical Performance

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

The effect of nickel coating on the mechanical properties and failure modes of continuous carbon fiber reinforced aluminum matrix composites

Effect of Multi-Walled Carbon Nanotubes and Carbon Fiber Reinforcements on the Mechanical and Tribological Behavior of Hybrid Mg-AZ91D Nanocomposites

Study of the C/ Mg Interface in Magnesium Matrix Composites Reinforced by Carbon (Graphite) Fiber

Microstructure, Interface and Strengthening Mechanism of Ni-CNTs/AZ91 Magnesium Matrix Composites

Research on Preparation and Properties of Carbon Fiber Reinforced Zinc-Based Aluminum Rich Alloy Composite

Mechanical properties and fabrication of carbon nanotubes reinforced AZ91D magnesium matrix nanocomposites

Effect of Ni addition on the behavior of dissimilar A356-AZ91/CeO2 aluminum-magnesium based composite fabricated by friction stir process technique

Interfacial and Fracture Behavior of Short-Fibers Reinforced AE44 Based Magnesium Matrix Composites

Microstructure and Tensile Properties of Magnesium Matrix Composite: Effected by Volume Fraction of Micron Sicp

Effect of Mg Content on the Mechanical Properties and Microstructure of Gr(F)/Al Composite

Study on Properties of Carbon Nanotube/Magnesium Matrix Composite