Abstract:In the present work, a novel Ni-Cu composite interlayer was prepared on the surface of A356 aluminum alloy solid insert using the chemical nickel-plating and electro-coppering technology, in order to restrain the generation of brittle phases and enhance the shear strength of A356 aluminum/AZ91D magnesium bimetal manufactured using a compound casting. The effect of the Ni-Cu composite interlayer on the microstructure, mechanical properties and corrosion resistance of the bimetal was studied. The results show that the Ni-Cu composite interlayer effectively restrained the generation of the brittle and hard Al-Mg intermetallic compounds (IMCs). The interface layer of the A356/AZ91D bimetal without Ni-Cu composite interlayer was composed of Al3Mg2, Al12Mg17, δ-Mg and Mg2Si phases, while the interfacial reactants of the A356/AZ91D bimetal with Ni-Cu composite interlayer were mainly Al3Ni, Ni (Cu), Cu (Ni), Mg2Cu and Al7Cu3Mg6 phases. With the application of the Ni-Cu composite interlayer, the thickness of the interface of the A356/AZ91D bimetal remarkably decreased from 1400 μm of the sample without Ni-Cu composite interlayer to 40 μm. The shear strength of the A356/AZ91D bimetal using Ni-Cu composite interlayer increased by 20.3% compared with that of the bimetal without Ni-Cu composite interlayer. The fractures of the A356/AZ91D bimetals with and without Ni-Cu composite interlayers belonged to a brittle rupture mode. The breakage of the bimetal with Ni-Cu composite interlayer mainly took place between the Ni-Cu layer and AZ91D matrix, while the rupture of the A356/AZ91D bimetal without Ni-Cu composite interlayer was located in the interface layer. The Cu(Ni) and Ni(Cu) layers had a lower nano-hardness than the Al-Mg IMCs, and the elasticity modulus for the Cu(Ni), Ni(Cu) and Al3Ni phases were higher compared to those of the Al-Mg IMCs. The results of corrosion test exhibited that the Ni-Cu composite interlayer had little influence on the corrosion resistance of the A356/AZ91D bimetal.

Effect of Ni addition on the behavior of dissimilar A356-AZ91/CeO2 aluminum-magnesium based composite fabricated by friction stir process technique

The behaviour of AZ91 magnesium-based alloy with Ni–Al 2 O 3 reinforcement

Improving mechanical properties of AZ91D magnesium/A356 aluminum bimetal prepared by compound casting via a high velocity oxygen fuel sprayed Ni coating

Development of dissimilar AA2014 and AA2024 based composite with nano-Si3N4 reinforcement by friction stir process technique

Tailoring AlSi7Mg0.3 composite properties with CoCrMoNbTi high entropy alloy particles addition via FSP technique

Influence of Vanadium and Niobium Carbide Particles on the Mechanical, Microstructural, and Physical Properties of AA6061 Aluminum-Based Mono- and Hybrid Composite Using FSP

Importance of Al2TiO5 particle on the mechanical and wear performance of stir cast AA6061 composite using Central Composite Design

Microstructure, Mechanical and Wear Properties of Short Carbon Fiber-Reinforced AM50 Magnesium Matrix Composite

Effect of nano-Sized Al2O3 Particles on Microstructure and Mechanical Properties of Aluminum Matrix Composite Fabricated by Multipass FSW

Influence of friction stir processing on microstructure and mechanical properties of AA6061 reinforced with Zr and Ni metallic particles

Microstructure and Mechanical Properties of Al-base Composites by Addition of Al–Ni–Co Decagonal Quasicrystalline Particles Through a Mechanical Stirring Route

Effects of Heat Treatment on the Interface Microstructure and Mechanical Properties of Friction-Stir-Processed AlCoCrFeNi/A356 Composites

Experimental investigation in enhancing the mechanical, wear and corrosion resistance properties of Al6061-SiC-NSA composites fabricated using stir casting process.

Comparative strengthening of intermetallic compounds produced in situ by friction stir processing on different aluminum alloy matrixes

Unveiling Enhanced Properties via Microstructural Evolution in Stir‐Cast Al6061 Composite Reinforced with AlCrFeNiTi High‐Entropy Alloy Particles.

Microstructure, mechanical properties and corrosion resistance of A356 aluminum/AZ91D magnesium bimetal prepared by a compound casting combined with a novel Ni-Cu composite interlayer

Influence of SAC and eggshell addition in the physical, mechanical and thermal behaviour of Cr reinforced aluminium based composite

Impact of friction stir welding parameters and Al2TiO5 reinforcement on the mechanical, wear, and corrosion performance of dissimilar welded aluminium composite joints

The Effect of Coating Grain Size on the Selective Oxidation Behaviour of Ni-Cr-Al Alloy

Microstructural, mechanical, and wear properties of ultrasonic assisted stir casted A356 Alloy/AlN composite

Development and characterization of a novel AA6061 composite reinforced with titanium aluminide via friction stir processing