Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Aluminum alloys feature impressive levels of strength, ductility, castability, wear resistance, and corrosion resistance, making them highly advantageous for the aviation and automotive industries. This study investigates the dry wear performance of hybrid nanocomposites (HNCs) produced using Al6061 as the matrix, with nano-fly ash (FA) and nano-yttrium oxide (Y2O3) as reinforcing agents, utilizing the stir-casting method. The weight percentage (wt-%) of FA was fixed at 4 wt-%, while the Y2O3 varied from 1 wt-% to 3 wt-%. The specimens were prepared following ASTM-G99 standards and tested using a pin-on-disc apparatus with an E31 steel disc under four different loads: 10 N, 20 N, 30 N, and 40 N. It has been observed that wear rate has been increased with the increase in the applied load. The maximum wear rate has been recorded for the base Al6061 alloy as 5.63 × 10−4 mm3/N-m at 40 N load due to its lower wear resistance and less hardness value. The addition of reinforcement particles in the base alloy results in the grain refinement and improvement in the load-bearing capacity. It has been found that at 40 N load, the Al-6061 alloy reinforced with (4 wt-% FA + 3 wt-% Y2O3) is 56.83% superior in terms of wear resistance (2.43 × 10−4 mm3/N-m) as compared to Al6061 base alloy. The hybrid nano-composite containing 4 wt-% FA + 3 wt-% Y2O3 showed the highest value of microhardness as 123.2 HV, which is 136% higher than that of base alloy due to the higher load-bearing characteristics of the reinforcement particles. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) have been employed to analyze both unworn and worn surfaces, revealing uniform dispersion of reinforcement particles, the formation of an oxide layer, micro-pitting, wear debris, and material delamination. Grain refinement has been examined using the line intercept method (ASTM E1382-97), and X-ray diffraction (XRD) confirmed the elemental composition of the nano-reinforcements.

Microstructural, mechanical, and wear properties of ultrasonic assisted stir casted A356 Alloy/AlN composite

Fabrication and Characterisation of Alumina/aluminium Composite Materials with a Nacre-Like Micro-Layered Architecture

Influence of AlN particles on microstructure, mechanical and tribological behaviour in AA6351 aluminum alloy

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Effect of Nanoaluminium Nitride Ceramic Particles on Microstructure, Mechanical Wear, and Machining Behavior of Al-Si-Mg Alloy Matrix Composites Produced by Bottom Pouring Type Stir Casting Route

Microstructural Evolution, Tensile Failure, Fatigue Behavior and Wear Properties of Al2O3 Reinforced Al2014 Alloy T6 Heat Treated Metal Composites

Microstructure and Mechanical Properties of ABOw and Nickel-Coated MWCNTs Reinforced 2024al Hybrid Composite Fabricated by Squeeze Casting

Importance of Al2TiO5 particle on the mechanical and wear performance of stir cast AA6061 composite using Central Composite Design

Analysis and Experimental Investigation of A356 Aluminium Alloy Hybrid Composites Reinforced with Gr-FE3O4-B4C Nanoparticles Synthesised by Selective Laser Melting (SLM)

Influence of TiC Particles on Mechanical and Tribological Characteristics of Advanced Aluminium Matrix Composites Fabricated through Ultrasonic-Assisted Stir Casting

Dry sliding wear characteristics of hybrid aluminum alloy with nano-fly ash and nano-yttrium oxide

Effect of nano-Sized Al2O3 Particles on Microstructure and Mechanical Properties of Aluminum Matrix Composite Fabricated by Multipass FSW

Enhanced mechanical and tribological properties of ultrasonically assisted stir-cast AA7075 metal matrix composites in challenging corrosive environments

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Enhancing the mechanical, wear and corrosion behaviour of stir casted aluminium 6061 hybrid composites through the incorporation of boron nitride and aluminium oxide particles

Microstructural Evolution & Mechanical Properties of ZrO2/GNP and B4C/GNP reinforced AA6061 Friction Stir Processed Surface Composites - A Comparative study

Influence of Vanadium and Niobium Carbide Particles on the Mechanical, Microstructural, and Physical Properties of AA6061 Aluminum-Based Mono- and Hybrid Composite Using FSP

Mechanical and dry sliding tribological characteristics of aluminium matrix composite reinforced with high entropy alloy particles

Development, mechanical characterization and analysis of dry sliding wear behavior of AA6082–Metakaolin metal matrix composites

Metallographic Study and Sliding Wear Optimization of Nano Si3N4 Reinforced High-Strength Al Metal Matrix Composites

Unveiling Enhanced Properties via Microstructural Evolution in Stir‐Cast Al6061 Composite Reinforced with AlCrFeNiTi High‐Entropy Alloy Particles.