Abstract:In the present study aluminium metal matrix composites (Al - MMCs) reinforced with different Wt% (2,3,4,5 and 6) of Silicon carbide (SiC) and hybrid composites of aluminium matrix reinforced with different Wt% (2,3,4,5 and 6) of SiC and constantly adding Boron carbide (B 4 C) with 2 wt% were fabricated using a cost effective powder metallurgy (PM) method and the mechanical alloying process. Mechanical properties like micro structure, phase analysis, hardness, compression strength, density, porosity and wear were characterized and investigated for the aluminium matrix composite (AMC) samples. Microstructural characterization of sintered samples was performed using a Scanning electron microscope with energy dispersive X-ray analysis. XRD analysis confirmed the peak identification of Aluminium, SiC and B 4 C particulates in the (Al-MMCs) composites. The hardness values of the composites Al+6wt% SiC and Al+4wt%SiC+2wt%B 4 C were seen as 20.6% higher than those of pure aluminium matrix. Increase in the hardness of the composite was seen due to grain refinement and resistance to dislocation motion. The existence of SiC particles in Al matrix was seen having the ability to improve the hardness value of the composites. The addition of SiC and B 4 C reinforcements in the Al matrix alloy has the potential to greatly increase the compressive strength of the AMCs. The density of hybrid composites was seen having a major impact on the influence of SiC and B 4 C particulates. The wear resistance of the hybrid composites were examined under load range of 5 and 10 N, with sliding speed of 0.1 m/s. The synergistic effect of reinforcing particles was seen as assisting the improvement of wear resistance due to the relative concentration of SiC and B 4 C. The incorporation of SiC and B 4 C reinforcements into the Aluminium matrix hybrid composite can substantially increase the hardness, compressive strength, and wear resistance of the composites.

Preparation of SiCp/Al MMCs by Ball Milling and Stir Casting

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Fabrication of Nano-Sic_p/al Composite by High Energy Ball Milling

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder

Aluminum Silicon Carbide Particulate Metal Matrix Composite Development Via Stir Casting Processing

Mechanical and Electrical Properties of Nano Al-Matrix Composites Reinforced with SiC and Prepared by Powder Metallurgy

Effect of Milling Time and Reinforcement Volume Fraction on Microstructure and Mechanical Properties of SiCp-Reinforced AA2017 Composite Powder Produced by High-Energy Ball Milling

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Structure Investigation of Ball Milled Composite Powder Based on AlSi5Cu2 Alloy Chips Modified by Sic Particles

Experimental Studies on Machinability of 14 Wt.% of Sic Particle Reinforced Aluminium Alloy Composites

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Preparation and Properties of Nano-sized SiC Particles Reinforced ADC12 Aluminum Matrix Composites

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites

Fabrication of AA2024/SiCp Metal Matrix Composite by Mechanical Alloying

A Novel Way to Produce Bulk SiCp Reinforced Aluminum Metal Matrix Composites by Friction Stir Processing

Sintering Bonding of SiC Particulate Reinforced Aluminum Metal Matrix Composites by Using Cu Nanoparticles and Liquid Ga in Air

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

INFLUENCE OF MILLING TIME ON GROWTH MORPHOLOGY AND MECHANICAL PROPERTIES OF ALUMINUM-SILICON-CARBIDE COMPOSITES

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Squeeze casting technique for fabricating SiCp/Al composites with lower volume fractions of SiC particles