Abstract:Previous experimental investigations (Hirakata et al. Int J Fract 145:261–271, 2007) have demonstrated that Si/Cu/SiN/Pt/C nano-cantilever is delaminated along the interface between Cu and Si layers when subjected to monotonically bending load, and the measured load-displacement relationship shows a nonlinear behavior. Based on the continuum mechanics model, this study carries out numerical simulations on the crack nucleation and propagation along the Si/Cu interface in order to clarify the effect of plasticity on the fracture behavior of the ductile nano-component. Exponential type of cohesive zone model (CZM) combined with finite element method was adopted to characterize the constitutive relationship of the Si/Cu interface. Two sets of simulations are performed, i.e., Cu layer obeys either linear elastic or Ramberg–Osgood elasto-plastic constitutive relation. The characteristic parameters of interfacial adhesion are extracted through calibration via experimental results. The simulation results indicate that (i) cohesive strength and work of separation are the dominating CZM parameters, and the exponential CZM is suitable for describing the interfacial delamination between the Cu and Si film layers; (ii) the Cu film layer in this nano-cantilever more favorably obeys a linear elastic constitutive relation; (iii) comparing to bulk Cu, nano-scale Cu has a much higher yield stress and hardening rate, which leads to little plastic deformation of the nano-cantilever specimen during the entire delamination process. The numerical predictions are in good agreement with the experimental results, wherein brittle fracture occurred during the Si/Cu interfacial delamination. And the nonlinear load-displacement behavior observed by the tests may be due to the cohesive law of the Si/Cu interface, instead of the plastic deformation of the Cu film layer.

Interfacial Delamination Of Pzt Thin Films

Cohesive Zone Modeling of Interfacial Delamination in Pzt Thin Films

Numerical simulation of interfacial delamination of PZT thin films by cohesive zone models

Experimental and Theoretical Investigations of Delamination at Free Edge of Interface Between Piezoelectric Thin Films on a Substrate

Delamination Test and the Effect of Free Edge on Interface Strength of Pzt Thin Films

Use of Nanomechanical Fracture-Testing for Determining the Interfacial Adhesion of PZT Ferroelectric Thin Films

Quantitative In-Situ Study of Strength-Governed Interfacial Failure Between H-Bn and Polymer-Derived Ceramic

Analysis on the Cracking of Thin Hard Films Considering the Effects of Interfacial Delamination

Reinvestigation of the effect of plasticity on delamination process of Si/Cu interface in a ductile nano-cantilever

Micro-Scale Delaminating and Buckling of Thin Film on Soft Substrate

Interfacial adhesion analysis of Pb(Zr0.52Ti0.48)O3 (PZT) thin films by nano-indentation test

ELASTO-PLASTIC COHESIVE ZONE MODELING OF DELAMINATION OF Si/Cu INTERFACE IN A NANO-CANTILEVER

Quantitative Characterization of the Interfacial Adhesion of Ni Thin Film on Steel Substrate: A Compression-Induced Buckling Delamination Test

A four-point bending technique for characterizing the interface fracture toughness between soft thin films and stiff substrates

Cohesive Zone Criterion for Cracking along the Cu/Si Interface in Nanoscale Components

OS13F017 Fracture Criterion for Cracking along the Cu/Si Interface in Nanoscale Thin Films by Cohesive Zone Model

Nonlinear electromechanical interfacial fracture for piezoelectric materials

Influence of Applied Electric Field on the Energy Release Rate for Cracked PZT/elastic Laminates

A Combined Simulation and Experimental Study on Cracking and Delamination Behavior at the Cu/Polyimide Interface of RDLs in Chiplet Package Subjected to Thermo-Mechanical Loads

Phase field-based cohesive zone approach to model delamination in fiber-reinforced polymer composites

201 Numerical Investigation on Cracking along the Cu/Si Interface with Nanoscale Stress Concentration by Cohesive Zone Model