Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Effect of PVDF dope rheology on the structure of hollow fiber membranes used for CO2 capture

Effect of solvent concentration on development of macrovoids of PVDF phase-diversion membranes

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Effect of Dissolving Temperature of Dopes on the Morphology of PVDF Membrane

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

Preparation of a novel dual-layer polyvinylidene fluoride hollow fiber composite membrane with hydrophobic inner layer for carbon dioxide absorption in a membrane contactor

Preparation and Characterization of PVDF/nonwoven Fabric Flat-Sheet Composite Membranes for Desalination Through Direct Contact Membrane Distillation

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

Effect of Non-Solvent Additive Concentration on CO2 Absorption Performance of Polyvinylidenefluoride Hollow Fiber Membrane Contactor

An Experimental Study PVDF and PSF Hollow Fiber Membranes for Chemical Absorption Carbon Dioxide

Preparation and characterization of polyvinylidene fluoride (PVDF) hollow fiber membranes

Effect of coating based on various hollow fiber packings on distillation of IPA/water system

Effect of Fiber Packing Density on Performance and Mass Transfer of Hollow Fiber Membrane Contactor

Fabrication and Characterization of Poly(vinylidene Fluoride)–polytetrafluoroethylene Composite Membrane for CO2 Absorption in Gas–liquid Contacting Process

Preparation Of Pvdf Hollow Fiber Membranes With High Adsorption Performance By One-Step Physical Coating And Chemical Cross-Linking

Effect of Polymer Content on the Properties of PVDF Electro-spinning Nanofiber Membrane for Membrane Distillation

Effect of Preparation Parameters on the Structure of PVDF Hollow Fiber Membranes

Optimization of Coating Solution Viscosity of Hollow Fiber‐supported Polydimethylsiloxane Membrane for CO2/H2 Separation

The Effects of PEI Hollow Fiber Substrate Characteristics on PDMS/PEI Hollow Fiber Membranes for CO2/N2 Separation