Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Preparation and Structural Control of Polyethylene Hollow Fiber Membranes

Effects of stretching on crystalline phase structure and morphology of hard elastic PVDF fibers

Preparation and Characterization of Pvdf-Hfp Microporous Membrane by Template Method

Fabrication of Hydrophilic and Sponge-Like PVDF/brush-like Copolymer Blend Membranes Using Triethylphosphate As Solvent

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Effect of Spin-Draw Rate and Stretching Ratio on Polypropylene Hollow Fiber Membrane Made by Melt-Spinning and Stretching Method

Effect of stretching on structure and properties of polyethylene hollow fiber membranes made by melt-spinning and stretching process

Preparation and characterization of polyvinylidene fluoride (PVDF) hollow fiber membranes

Microporous PVDF membranes via thermally induced phase separation (TIPS) and stretching methods

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

Study on the Cross-Section Irregular Shape of Prepared PVDF Hollow Fiber Membrane

Preparation of poly(4-methyl-1-pentene) asymmetric or microporous hollow-fiber membranes by melt-spun and cold-stretch method

Preparation and properties of electrospun poly(vinylidene fluoride) membranes

Study on preparation, structure and properties of hard elastic PVDF fibers

Effect of Spinning Conditions on the Structure and Performance of Hydrophobic PVDF Hollow Fiber Membranes for Membrane Distillation

Preparation of High Strength Poly(vinylidene Fluoride) Porous Membranes with Cellular Structure Via Vapor-Induced Phase Separation

The improvement of water flux and mechanical strength of PVDF hollow fiber membranes by stretching and annealing conditions

Effect Of Preparation Methods On Crystallization Behavior And Tensile Strength Of Poly(Vinylidene Fluoride) Membranes

Preparation and properties of poly (vinylidene fluoride) membranes via the low temperature thermally induced phase separation method

Robust preparation and reinforcement mechanism study of PVDF hollow fiber membrane with homogeneous fibers