Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Preparation Of Pvdf Hollow Fiber Membranes With High Adsorption Performance By One-Step Physical Coating And Chemical Cross-Linking

Porous poly(vinylidene fluoride) membrane modified with hyperbranched poly(amine-ester)

Porous Membranes Modified by Hyperbranched Polymersi. Preparation and Characterization of PVDF Membrane Using Hyperbranched Polyglycerol As Additive

In Situ Crosslinking of Hyperbranched Polyglycerol in Casting Solutions and Its Effect on the Structure and Properties of Porous Pvdf Membranes

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Preparation and Characterization of Pvdf-Hfp Microporous Membrane by Template Method

Fabrication of High-Flux PTFE Hollow Fiber Membranes Through Nonionic Surfactant Infiltration Coupled with Mussel-Inspired Chemistry Coating

Modification of Porous Poly(Vinylidene Fluoride) Membrane Using Amphiphilic Polymers with Different Structures in Phase Inversion Process

Developing PVDF Hollow Fiber Membrane Enhanced by Braided Tube and Modified by Bionic Coating for Treating Aldehyde-Containing Wastewater

Study on the Modification of PVDF Membrane (1) Preparation of Hydrophilic PVDF Hollow Fiber Membrane with PVP Via Cross-Linking Reaction

Preparation of hydrophilic and fouling resistant poly(vinylidene fluoride) hollow fiber membranes

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Preparation and characterization of polyvinylidene fluoride (PVDF) hollow fiber membranes

Hydrophilic modification of poly(vinylidene fluoride) membrane with poly(vinyl pyrrolidone) via a cross-linking reaction

Preparation of hydrophilic polypropylene hollow fiber membranes by UV modification

An Investigation on the Antifouling Ability of Pvdf Membranes by Polydopa Coating

Preparation of Multipurpose Polyvinylidene Fluoride Membranes via a Spray-Coating Strategy Using Waterborne Polymers

Improving multifunctional properties of the polyvinylidene fluoride (PVDF) membrane with crosslinked dialdehyde-starch (DAS) and polyethyleneimine (PEI) coating

Preparation Of Sulfobetaine-Grafted Pvdf Hollow Fiber Membranes With A Stably Anti-Protein-Fouling Performance

PVDF ultrafiltration membrane with enhanced mechanical and filtration performance by hydrophilic pH-response nanofibers modification

Surface modification of a PVDF membrane by co‐grafting hydroxyl and zwitterionic polymers to enhance wettability and antifouling property