RF Receiver Design for CSRH

JI Guo-shu,DOU Yu-jiang,WANG Wei,LIU Fei,CHEN Zhi-jun,ZHANG Jian,YAN Yi-hua

DOI: https://doi.org/10.14005/j.cnki.issn1672-7673.2006.02.007

2006-01-01

Abstract:The analogy receiver structure of CSRH experiment-two elements interferometer is presented in this paper.The sensitivity,dynamic range,noise figure and gain distribution of the instrument are discussed.The analogy receiver for CSRH is designed on experiment result.

What problem does this paper attempt to address?

A Prototype Digital Correlation Receiver for Two-element Interferometer Experiment

ZHANG Jian,YAN Yi-hua,LIU Fei,WANG Wei

DOI: https://doi.org/10.3969/j.issn.1672-7673.2006.02.008

2006-01-01

Abstract:For designing and building Chinese Spectral Radioheliograph(CSRH),we have carried out a two-element interferometer experiment.In the test,a prototype digital correlation receiver has been designed for the signal processing below the 200 MHz intermediate frequency.In this paper,we describe the design of the digital receiver,which includes high-speed ADC,band-pass filters,mixer,delay line and one-bit correlator.Finally,a simulation of signal processing of the digital correlation receiver is given.
A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

Hui Nie,Tiancheng Yu,Jiangbo Chen,Jiabing Liu,Dongdong Liu,Xiaopeng Yu,Qun Jane Gu,Zhiwei Xu

DOI: https://doi.org/10.1109/tcsii.2024.3423839

2024-01-01

IEEE Transactions on Circuits & Systems II Express Briefs

Abstract:This brief presents a 0.5-8 GHz CMOS RF receiver front-end (RxFE) tailored for cognitive radio (CR) and digital phased array (DPA) applications. The RxFE comprises a wideband mixer with noise suppression capability, along with a reconfigurable band-pass filter (BPF) designed to adapt to different intermediate frequencies (IFs) and signal bandwidths (SBWs). Additionally, the BPF functions as a programmable gain amplifier (PGA), enabling support for a large dynamic range with fine gain adjustment. The BPF offers a programmable center frequency (CF) range from 250 MHz to 450 MHz with a 5 MHz step, as well as support for tunable passbands from 60 MHz to 240 MHz with 5 MHz resolution. The RF RxFE provides a gain control range of 15-to-55 dB with a 0.5 dB gain step. Fabricated in a standard 55 nm CMOS process, the prototype occupies an area of 2.29 mm2 including pads, consuming 75.6mW power without an on-chip high-IF BPF and 226.8mW with it at 2.3GHz LO input. Measurement results indicate that the prototype achieves approximately 10 ns gain switching time and 350 ns frequency hopping time when driven by an external fast-switching local oscillation (LO) signal, attributed to its high IF architecture. The receiver demonstrates exceptional agility, meeting the stringent requirements of CR and DPA applications.
A Sub-GHz CMOS Low-IF Receiver for Lot Applications

Liying Cai,Xiaopeng Yu,Hanqi Gao,Suhao Chen,Xiong Song,Lingchang Chen,Kai Huang,Dandan Zheng

DOI: https://doi.org/10.1109/iws49314.2020.9360175

2020-01-01

Abstract:A sub-GHz RF receiver with low power consumption and low noise figure (NF) is presented in this paper. It is featured with an improved shunt feedback low noise amplifier (LNA), which obtains a balance among gain, power consumption and noise figure, etc. Moreover, a complex filter with tunable central frequency and bandwidth is proposed in the intermediate frequency (IF) range. It shows a high image rejection rate and a wide range of gain. The receiver, implemented using 0.13-μm CMOS technology, exhibits a noise figure of 4.45 dB, a maximum voltage gain of 85.2 dB and a high image rejection rate of 79.0 dB in measurements. For 1.2V supply voltage, the DC power consumption is 3.4mW/26.6 μW under working and sleep modes respectively.
Site Survey and RFI Test for CSRH

CHEN Zhi-jun,YAN Yi-hua,LIU Yu-ying,ZHANG Jian,WANG Wei

DOI: https://doi.org/10.3969/j.issn.1672-7673.2006.02.011

2006-01-01

Abstract:The CSRH will be a broadband synthesis-imaging array,and the instrument demands a site with low levels of Radio Frequency Interference(RFI) over this entire band.The site surveys and RFI tess for the CSRH project in Hebei province and Inner Mongolia are described in this paper.Several sites in the Hebei province and Inner Mongolia are being considered.For all sites,the climate,traffic and spectrum environment are discnssed.
CHINESE SPECTRAL RADIOHELIOGRAPH: CURRENT INVESTIGATION IN DIGITAL RECEIVER AND CONTROL SYSTEM

Wei Wang,Fei Liu,Yihua Yan,Jian Zhang,Linjie Chen,Junbo He,Zhijun Chen,Guoshu Ji,Yujiang Dou

2009-01-01

Abstract:In this paper, I will introduce several reasonable design of digital receiver and control subsystem in CSRH project. For digital receiver it seems reachable to get high resolution correlation result in both time domain and frequenc y domain by employing high sampling rate ADC (~1 GHz) and polyphase filter bank. By combining with FFT, frequencies in which we are interested could be synthesized and the band width of certain frequency can be set flexibly as well. Another design is from traditiona l heterodyne and complex quadrature mixing, as a result, correlation results are in tim e domain. Control subsystem in CSRH is designed based on distributed control network.
A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

Zhaolin Yang,Jing Jin,Xiaoming Liu,Taotao Yan,Xiaopeng Yu,Jianjun Zhou

DOI: https://doi.org/10.1109/tmtt.2021.3072584

IF: 4.3

2021-01-01

IEEE Transactions on Microwave Theory and Techniques

Abstract:This article presents a fully differential high-dynamic-range direct-conversion receiver for sub-1-GHz band applications in a 180-nm CMOS technology. The integrated self-adaptive multipart automatic gain control (AGC) loops are designed to cope with large input signal. In the radio frequency (RF) domain, a gain-adjustable noise-canceling balun low-noise amplifier (LNA) and a high-linearity RF variable gain amplifier (VGA) are co-designed to keep a steady differential output power for the mixer stage. In baseband (BB), a novel gain distribution method is proposed to protect BB circuits from saturation. To prove the concept, one of the most typical and strict application scenarios in the sub-1-GHz band, digital television (DTV) standard, is analyzed and chosen as the design target. The receiver achieves a noise figure (NF) of 3.6–4.6 dB in the ultrahigh-frequency (UHF) band. A wide gain tuning range of 128.8 dB is realized in this work, featuring fully integrated AGC loops. The programmable bandwidth of the low-pass filter (LPF) can be adjusted from 1 to 4 MHz, supporting 2-/6-/7-/8-MHz signal channels. The maximum in-band third-order input-referred intercept point (IIP3) is 10 dBm under the conversion gain of 0 dB. The receiver consumes 49.56 mA from a 1.8-V voltage supply and occupies an area of 3.56 mm2.
High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

Yiming Han,Fengjie Wang,Jiarui Liu,Zhiyu Wang,Faxin Yu

DOI: https://doi.org/10.3390/electronics10161966

IF: 2.9

2021-01-01

Electronics

Abstract:To improve the linearity of direct conversion receivers (DCRs), two high-linearity methods for high second-order intercept points (IP2s) and high third-order intercept points (IP3s) are proposed. To improve IP3s, a transconductance equalization technique for a complementary input operational amplifier (OPAMP) is proposed in an active-RC low-pass filter (LPF), while a digital-analog hybrid DC offset calibration (DCOC) method is proposed to improve IP2s. For one thing, the proposed transconductance equalization technique employs a pair of resistors to guarantee high voltage gain for an OPAMP with two-stage Miller topology under a high-input voltage swing to improve linearity with little deterioration of the noise performance. For another, during the DCOC method, the low-noise amplifier is turned off and replaced by an equivalent resistance of the output impedance of the low-noise amplifier to ensure the accuracy and effectiveness of the DCOC method. Fabricated in 40-nm CMOS technology, the receiver with proposed methods can realize a noise figure of 2.6–3.5 dB in the full frequency band, with an OIP3 of 28 dBm, an IM2 more than 70 dBc, and a remaining DC of −53.2 dBm under the total voltage gain of 60 dB.
A 434/868 Mhz Cmos Low-If Receiver with I/Q Imbalance Calibration for Srds Application

Li Juan,Zhao Feng,Ye Guojing,Hong Zhiliang

DOI: https://doi.org/10.1088/1674-4926/30/3/035003

2009-01-01

Journal of Semiconductors

Abstract:A receiver for SRDs implemented by the 0.35 mu m CMOS process is presented. The receiver, together with the ADC, power amplifier (PA), frequency synthesizer and digital baseband has been integrated into a single chip solution. Low cost and low power requirements are met by optimizing the receiver architecture and circuit topology. A simple mixed-signal mode I/Q imbalance calibration circuit is proposed to enhance the IRR (image rejection ratio) so as to raise the BER. From a single 3 V power supply, the receiver consumes 5.9 mA. The measurement result shows that the receiver achieves reference sensitivity of -60 dBm and a control gain of 60 dB. The S-11 reaches -20 dB at 433 MHz and -10 dB at 868 MHz without off-chip impedance match network. The die area is only 2 mm(2) including the bias circuit.
The Design And Implement Of A Receiver For Fsk Signal

Liu Xiao-Peng,Han Yan,Zhong Dong-Dong,Wang Ming-Yu

DOI: https://doi.org/10.4028/www.scientific.net/AMM.190-191.739

2012-01-01

Abstract:A novel frequency shift keying (FSK) receiver is presented, including receiving antennas, a low noise amplifier (LNA), band-pass filters (BPF) and a novel all-digital 2-level FSK demodulator. The Mat lab simulation results of the all-digital FSK demodulator show that it can improve bit error ratio (BER) performance compared with pseudo-coherent FSK demodulation (PCFSK). The novel FSK demodulator defined using Verilog HDL is easy to be implemented on Field Programmable Gate Array (FPGA) and in CMOS integrated circuit. The whole FSK receiver designed and implemented on a PCB board can receive FSK signal and send the recovered data to computer through RS-232 interface.
Array Configuration and Feed Design for CSRH

WANG Wei,YAN Yi-hua,ZHANG Jian,JI Guo-shu,CHEN Zhi-jun

DOI: https://doi.org/10.3969/j.issn.1672-7673.2013.01.004

2006-01-01

Abstract:The Chinese Spectral Radioheliograph(CSRH) will be a solardedicated radio interferometric array that will be optimized to carry out imaging spectroscopy of the Sun,to produce high spatial resolution,high time resolution and high frequency resolution images of the Sun simultaneously in cm-dm wave range.Some work on array configuration and feed design for CSRH is described in this paper.On the array configuration,the four array design plans-"T","Y", irregular,and spiral configuration are discussed.It is argued that self-similar spiral geometries will be fit for CSRH.The scientific demands on feed design and ANSERLIN antenna used in our recent experiments are described.
Optical Fiber Transmission Analysis for CSRH

WANG Wei,CHEN Zhi-jun,JI Guo-shu,LIU Fei,DOU Yu-jiang,ZHANG Jian,YAN Yi-hua

DOI: https://doi.org/10.3969/j.issn.1672-7673.2006.02.007

2006-01-01

Abstract:The basic scheme,principle and advantage of optical fiber link in the radio telescope are presented.Some main performances of CSRH: noise figure,dynamic range,and phase shift etc.are also discussed.
Progress on Chinese Solar Radioheliograph in Cm-Dm Wavebands

YAN Yi-hua,ZHANG Jian,CHEN Zhi-jun,JI Guo-shu,WANG Wei,LIU Fei

DOI: https://doi.org/10.3969/j.issn.1672-7673.2006.02.001

2006-01-01

Abstract:A new Chinese radioheliograph project(CSRH) at multiple frequencies in the dm-cm wave range with 100 antennas of is proposed.A prototype study of 2-element interferometer has been built and tested for overall design since 2004.The prototype system includes two 4.5m antennas,feed and LNA(low noise amplifier),optical transmitter,optical fibril,optical receiver,RF(radio frequency) receiver,and digital correlator receiver.The site survey for future location of the CSRH array is carried out and a radio quiet region in Inner Mongolia appears promising.The progress about the project is introduced in the present work.
CSRH Antenna Control Experiment and Research

LIU Fei,ZHANG Jian,CHEN Zhi-jun,YAN Yi-hua,WANG Wei

DOI: https://doi.org/10.3969/j.issn.1672-7673.2006.02.009

2006-01-01

Abstract:We implemented the two-antenna synchronized control at short baseline distance (～8m) in the radio heliograph spectrometer test.In addition,we designed the scheme of two-antenna synchronized control at long baseline distance(～1km).The system control of radio heliograph spectrometer is also concerned.
R&D of RF-IF amplifier subassembly with STC

Jiang Ying,Wang Qin,Deng Kaihua,Ye Xiaoling,Liu Yang

DOI: https://doi.org/10.3969/j.issn.1001-7100.2007.04.024

2007-01-01

Abstract:The design of RF-IF amplifier subassembly is introduced.It consists of Sensitive Time Control(STC),low noise amplifier,image reject mixer,pre-IF amplifier,STC control circuit and PIN voltagetuned attenuator.The design methods and results of each unit and the whole circuit of the subassembly are also introduced.
Five-Element Digital Receiver for the Chinese Spectral Radio Heliograph

An Zhao,Yihua Yan,Jian Zhang,Fei Liu

2014-01-01

Abstract:The Chinese Spectral Radioheliograph (CSRH) is a solar-dedicated radio interferometric array that will produce high spatial resolution, high time resolution and high frequency resolution images of the Sun simultaneously in cm-dm wave range. A Five-element Digital Receiver System (FDRS) is developed to pretest and calibrate the Chinese Spectral Radioheliograph (CSRH) by using the Field Programmable Gate Array (FPGA). Meanwhile, an agile and flexible procedure of the signal processing is achieved. The design of the FDRS is outlined. The design and simulations of the modules are shown. Finally, a testing result of the correlation receiver system is demonstrated.
A New Architecture of UHF RFID Digital Receiver for SoC Implementation

Chenling Huang,Yuan Liu,Yifeng Han,Hao Min

DOI: https://doi.org/10.1109/wcnc.2007.312

2007-01-01

Abstract:A new architecture of UHF (ultra high frequency) RFID (radio frequency identification) digital receiver for SoC (system-on-chip) implementation is presented in this paper. For the system requirements, the design uses a unique two-stage correlation algorithm to estimate the frequency of the received data which may have large frequency deviation and also to achieve fast data decoding. Considering the single chip integration, we optimize the implementation for both low hardware cost and quick response. The function of the design is verified through FPGA implementation on Altera StratixII EP2S60 with great performance and its chip design used the SMIC 0.18mum process along with other parts of the UHF RFID interrogator chip.
Design of Parallel Multi-Channel Receiver Based on GC5016

XU Zhi-peng,ZHANG Xing-gan,TANG Lan,BAI Ye-chao

DOI: https://doi.org/10.3969/j.issn.1004-373x.2012.01.029

2012-01-01

Abstract:A scheme of parallel multi-channel receiver is introduced.The scheme is based on the theory of multi-rate signal processing and the broadband band-pass sampling software radio architecture.It used TI′s digital up/down-converter GC5016 as the core chip of the receiver.The structure and function of GC5016 is introduced.The theoretical analysis and simulation research of CIC and PFIR used in re-sampling extraction and filter integral are proposed.CPLD as the main peripheral device generated configuration timing and completed reconfiguration under the control of the PC.The scheme has high integration,flexibility and wide range of application by using programmable devices extensively.
A 28-/60-GHz Dual-Band Receiver Front-End With Sideband-Selection Technique in 65-nm CMOS

Yiming Yu,Zijian Ouyang,Xingnuo Huo,Chenxi Zhao,Huihua Liu,Yunqiu Wu,Kai Kang

DOI: https://doi.org/10.1109/tcsi.2024.3432171

2024-10-04

IEEE Transactions on Circuits and Systems I Regular Papers

Abstract:This article presents a dual-band receiver front-end based on a reconfigurable Hartley architecture with double frequency conversion for millimeter-wave wireless communication. By controlling working states of band-select switches, the receiver is able to reach different RF bands without increasing or altering local-oscillator (LO) and intermediate-frequency bands. To reduce power consumption and save chip area, RF quadrature mixers are co-designed with the last stage of a dual-band low-noise amplifier and reuse its dc current. In addition, a self-mixing frequency tripler with a transformer-based compact hybrid is developed to multiply an input LO and provide quadrature LO signals for the RF mixers. The prototype receiver is demonstrated in a 65 nm CMOS process. Measurement results show that the receiver successfully covers two frequency bands of 24.6~28 GHz and 55.6~60 GHz, and the corresponding peak conversion gains are up to 24.5 dB and 26.3 dB, respectively. In these two bands, the minimum single-sideband noise figures are 7.5 and 7.8 dB. The tested image-rejection ratio of the dual-band receiver is better than 30 dB in both 26.5~30.0 GHz and 57.5~60.5 GHz bands. Besides, the receiver also demonstrates its capability of supporting up to 256QAM modulation and 3.2-Gb/s data-rate transmission.

engineering, electrical & electronic
Research on Receiver Anti-RFI of Delingha 13.7 M Telescope

Li Zhen-qiang,Li Ji-bin,Zhang Xu-guo,Shan Wen-lei,Xu Ye,Zuo Ying-xi,Zhang Hai-long,Jin Feng-juan,Sun Ji-xian,Lu Deng-rong,Ju Bing-gang

DOI: https://doi.org/10.1016/j.chinastron.2019.11.009

2019-01-01

Chinese Astronomy and Astrophysics

Abstract:In astronomical observations, the radio frequency interference (RFI) will cause pseudo spectra and reduce the reliability and validity of observational data. The RFI mitigation, which includes many technical innovations of devices and the method studies of data processing, aims at reducing the influence of RFI on the radio astronomical observation. Various efforts were made to improve the anti-RFI capability of the multi-beam receiver (Superconducting Spectroscopic Array Receiver, SSAR) of the Delingha 13.7 m telescope. The interference transmission path was analyzed. The concepts of the device RFI direct coupling coefficient and the device RFI system coupling coefficient were proposed. The proportions of interference introduced in the receiver system by the different devices were quantified, and the interference-susceptible devices in the system were located. After the anti-RFI treatment of the interference-susceptible devices, the anti-RFI capability of the receiver system is improved by 30 dB in average, and the astronomical observation efficiency of the telescope is increased by more than 10%.

RF Receiver Design for CSRH

A Prototype Digital Correlation Receiver for Two-element Interferometer Experiment

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

Site Survey and RFI Test for CSRH

CHINESE SPECTRAL RADIOHELIOGRAPH: CURRENT INVESTIGATION IN DIGITAL RECEIVER AND CONTROL SYSTEM

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A 434/868 Mhz Cmos Low-If Receiver with I/Q Imbalance Calibration for Srds Application

The Design And Implement Of A Receiver For Fsk Signal

Array Configuration and Feed Design for CSRH

Optical Fiber Transmission Analysis for CSRH

Progress on Chinese Solar Radioheliograph in Cm-Dm Wavebands

CSRH Antenna Control Experiment and Research

R&D of RF-IF amplifier subassembly with STC

Five-Element Digital Receiver for the Chinese Spectral Radio Heliograph

A New Architecture of UHF RFID Digital Receiver for SoC Implementation

Design of Parallel Multi-Channel Receiver Based on GC5016

A 28-/60-GHz Dual-Band Receiver Front-End With Sideband-Selection Technique in 65-nm CMOS

Research on Receiver Anti-RFI of Delingha 13.7 M Telescope