Abstract:This paper presents a 0.2 similar to 3.8-GHz in-band (IB) full-duplex (FD) mixer-first receiver based on a vector self-interference (SI) canceller. To ensure the wideband orthogonality of the reconstructed SI signal while minimizing the noise figure (NF) degradation in FD mode, a low insertion loss two-stage polyphase filter (PPF) with a lacking resistance and capacitance (LRC) structure is used in the SI canceller. A 6-bits passive capacitor digital to analog converter (C-DAC) attenuator not only realizes the high-precision amplitude adjustment of the reconstructed SI signal but also avoids the linearity limitation of the back-end modules of the canceller and reduces the noise contribution of the front-end modules at the canceller output. A four-phase mixer-first receiver with enhanced out-of-band (OOB) interference suppression is designed to provide sufficient linearity to reduce the SI-induced nonlinear distortion. As a proof of concept, a prototype FD receiver is fabricated in CMOS 65 nm technology and measured in chip-on-board (COB) package. Measurement results show that it can operate in the frequency range of 0.2 similar to 3.8-GHz with more than 25 dB SIC amount for 10 MHz bandwidth (BW) 64-QAM modulated signals in fixed (30 dB) channel attenuation test setup. The receiver achieves OOB input-referred third-order intercept point (OOB-IIP3) of +24 dBm and OOB input-referred second-order intercept point (OOB-IIP2) of +82 dBm at 1-GHz local oscillator (LO) frequency. In FD mode, the NF degradation is <= 1.5 dB. The effective IB-IIP3 and effective IB-IIP2 are enhanced by 15 dB and 28 dB, respectively. The power consumption of entire FD receiver including the SI canceller is less than 44 mW. The active chip area is 0.55 mm(2).

A 434/868 Mhz Cmos Low-If Receiver with I/Q Imbalance Calibration for Srds Application

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A 0.6V 32.5mw Highly Integrated Receiver for 2.4ghz ISM-Band Applications

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

A Frequency-Domain I/Q Imbalance Calibration Algorithm for Wideband Direct Conversion Receivers Using Low-Cost Compensator.

20 . 6 A 0 . 6 V 32 . 5 mW Highly Integrated Receiver for 2 . 4 GHz ISM-Band Applications

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A 0.1–5.0 GHz Flexible SDR Receiver with Digitally Assisted Calibration in 65 Nm CMOS

A 0.1&#x2013;5ghz SDR Transmitter with Dual-Mode Power Amplifier and Digital-Assisted I/Q Imbalance Calibration in 65nm CMOS

A 0.1–5ghz Flexible SDR Receiver in 65nm CMOS

A 1.2V 0.1&#x2013;3ghz Software-Defined Radio Receiver Front-End in 130nm CMOS

A 1.8V CMOS direct conversion receiver for a 900MHz RFID reader chip

A 1.65 Mw Direct-Conversion Receiver for UHF RFID Readers

An 89 Μw MICS/ISM Band Receiver for Ultra-Low-power Applications.

A 0.2~3.8-Ghz Full-Duplex Receiver with More Than 25 Db Self-Interference Cancellation Using a C-DAC-Based Vector Canceller.

A 2.4 GHz 2.9 Mw Zigbee RF Receiver with Current-Reusing and Function-Reused Mixing Techniques

A Low Power 35 Ghz Cmos Uwb Receiver Front-End

A 0.1–4 GHz SDR receiver with reconfigurable 10–100 MHz signal bandwidth in 65 nm CMOS

A 0.2~3.8-GHz Full-Duplex Receiver With More Than 25 dB Self-Interference Cancellation Using a C-DAC-Based Vector Canceller