Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Amorphous Alloys Synthesized by Interface-Assisted Ion Beam Mixing in the Ag–W System with the Largest Positive Heat of Formation

Study of metastable alloy formation by thermodynamic calculation and ion beam manipulation in an equilibrium immiscible Au–W system

Formation of Amorphous Alloys by Ion Beam Mixing and Its Multiscale Theoretical Modeling in the Equilibrium Immiscible Sc-W System.

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Unusual Alloying Behavior Observed in the Immiscible AgMo and AgNb Systems under Ion Irradiation

Amorphous Alloy Formation in Immiscible Cu-Ta and Cu-W Systems by Atomistic Modeling and Ion-Beam Mixing

Ion Beam Manipulation to Fabricate Ordered Layered Structures and Amorphous Alloys in Some Highly Immiscible Binary Metal Systems

Structural Stability and Characteristics of the Metastable Ag-W Phases Studied by Ab Initio and Molecular Dynamics Calculations

Solid-State Alloying in Binary Systems with a Positive Heat of Mixing

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Amorphous Alloys Formed by Ion Mixing or Solid-State Reaction in Immiscible Y-Refractory Metal Systems and Their Elastic Properties

Metastable alloys synthesized by ion mixing in immiscible Ti–Nb and Ti–Ta systems

Non-equilibrium Alloy Formation in the Ag–Zr System by Ion Beam Mixing

Atomistic Modeling of Metastable Phase Selection of a Highly Immiscible Ag–W System

Amorphization in the AlC System by Mechanical Alloying

Formation and structural anomaly of the metastable phases in an immiscible Ag - Mo system studied by ion beam mixing and molecular dynamics simulation

Role of Interface in Ion Mixing Induced Amorphization in the Ag–Mo System with Very Positive Heat of Formation

Nanoscale Phase Separation and Local Icosahedral Order in Amorphous Alloys of Immiscible Elements

Interface-Driven Solid-State Alloying in an Immiscible Cu-W System

Formation of Crystalline and Amorphous Solid Solutions of W–Ni–Fe Powder During Mechanical Alloying

Nonequilibrium Alloy Formation In The Immiscible Cu-Mo System Studied By Thermodynamic Calculation And Ion Beam Mixing