Abstract:Transverse mechanical properties of titanium matrix composites (TMCs) play an important role during its engineering service. Although SiCf / TC17 composite is one of the most promising TMC candidates for aeroengine, as we know its transverse properties have not been reported yet until now. In this work, the transverse strength of single SiC fiber reinforced TC17 composite was evaluated using cruciform specimen. The surface and cross-section of fractured specimen were investigated by SEM to determine the failure position during tensile test. Finite element simulation method was also used to analyze the mechanism of interfacial failure and crack propagation. During the transverse tensile test of single fiber specimen, the initial non-linearity in the stress-strain curve occurred at the stress of (271 +/- 12) MPa, which indicated the beginning of fiber-matrix interface failure. SEM observation showed that the crack in the center of sample appeared at the interface of reaction layer and carbon coating with a 24 degrees similar to 68 degrees angle to the applied loading direction and its length extended with the increase of the applied stress. The finite element simulation results based on bilinear cohesive element model showed that transverse fracture of composite interface was shear failure mode, which agreed well with the test results. Before the occurrence of non-linearity in the stress-strain curve, the crack initiated at the circular interface between reaction layer and carbon coating with a 40 degrees similar to 50 degrees angle to the applied loading direction. Crack initiation locations in test samples were different with those in simulation samples, because the actual composite interface was rough and some micro-flaws formed in the interface, whereas it was assumed to be an ideal rigid interface for simulation. Then the crack propagated along both circumferential and axial directions because of the shear stress. With the crack growing, the interface close to 0 degrees angle to the applied loading direction failed first caused by the radial tensile stress, whereas the interface near 90 degrees failed later as a result of circumferential shear stress. After complete failure of the interface, stress redistribution occurred around the SiC fiber and the interface separation increased with the increasing of the applied load, which gave rise to the yielding and deforming of the matrix near fiber until the final fracture of the composite.

SEM in Situ Study on the Mechanical Behaviour of SiCf/Ti Composite Subjected to Axial Tensile Load

Experiment and FEM Study on Uniaxial Tensile of SiCp/Al

Fatigue crack growth rate in SiC fiber reinforced titanium matrix composites

Research on Single SiC Fiber Reinforced TC17 CompositesUnder Transverse Tension

In-situ Characterization on Crack Propagation Behavior of SiCf/SiC Composites During Monotonic Tensile Loading

Fatigue Properties and Fracture Analysis of a SiC Fiber-Reinforced Titanium Matrix Composite

Fatigue Behavior and Damage Evolution of Sic Fiberreinforced Ti-6al-4v Alloy Matrix Composites

Failure Evaluation of a SiC/SiC Ceramic Matrix Composite During In-Situ Loading Using Micro X-ray Computed Tomography

Study of Interfacial Stress Distribution in SiC Fiber Reinforced Titanium Matrix Composites on Transverse Tensile Tests

The Effect of Fabrication Processes on the Mechanical and Interfacial Properties of SiCf/Cu–matrix Composites

Unveil the Size-Dependent Mechanical Behaviors of Individual Cnt/Sic Composite Nanofibers by in Situ Tensile Tests in Sem

In Situ X-ray Imaging and Numerical Modeling of Damage Accumulation in C/SiC Composites at Temperatures Up to 1200 ℃

Interfacial Behavior and Mechanical Properties of SiC_f/Ti6Al4V/Cu Composite

In Situ Detection of Damage in the SiC<sub>f</sub>/Ti6242 Composite During the Thermomechanical Fatigue Test

Stress Field and Damage Evolution in C/SiC Woven Composites: Image-Based Finite Element Analysis and in Situ X-Ray Computed Tomography Tests

Multiscale Failure Mechanism Analysis of SiC Fiber-Reinforced TC17 Composite Subjected to Transverse Tensile Loading at Elevated Temperature

Internal Damage Evolution of C/SiC Composites in Air at 1650 °C Studied by In-Situ Synchrotron X-ray Imaging

Study on Fracture Behavior of Particulate Reinforced Magnesium Matrix Composite Using in Situ SEM

Molecular Dynamics Study on Tensile Behavior of Sic Nanofiber/C/Sic Nanocomposites

In-situ study of the fracture behavior of SiCf/SiC composite material under three-point bending

Fatigue Behaviors of C/Mo Double-Coated SiC Fiber-Reinforced Ti6Al4V Composites with Varied Interfacial Microstructure