Abstract:LSCOp and LSCOw powders were synthesized by a sol-gel method. And then Ag-LSCOp and Ag-LSCOw electrical contact composites were fabricated by high-energy ball milling and sintering process with LSCO powders as the second reinforcement phase. The effects of pH and pre-treating temperature of sol on the microstructure of LSCO powder were studied. The effects of molding pressure and sintering institution on the electrical and mechanical properties of Ag-LSCO contacts were investigated. The microstructure and phase of LSCO powders and resistivity and hardness characteristics of the Ag-LSCO electrical contact material were tested by scanning electron microscopy (SEM), X-ray diffractometer (XRD), D6OK digital metal conductivity meter and HVS-1000 digital microhardness tester. The results show that LSCOp is obtained at pH= 9.5 and calcining institution of 700 degrees C for 8 h when using single citric acid as the gelling agent, but LSCOw is obtained with citric acid and EDTA used as complex gelling agents. Ag/LSCOw electrical contact materials would be prepared with the molding pressure of 1100 MPa, sintering temperature of 900 degrees C and sintering time of 6 h. And when using LSCOw powder as the second reinforcement phase, Ag-LSCOw electrical contacts show lower resistivity than Ag-LSCOp.

Progress on Preparing LaGaO3 Based Sr-and Mg-doped Electrolyte by Wet Chemical Method

Improvement in the Sintering and Electrical Properties of Strontium- and Magnesium-Doped Lanthanum Gallate by MoO3 Dopant

Synthesis and Properties of Sr-and Mg-doped LaGaO_3 Materials

Synthesis and Characterization of La0.9Sr0.1Ga0.8Mg0.2O3−δ Intermediate-Temperature Electrolyte Using Conventional Solid State Reaction

PROCESSING AND ELECTRICAL PROPERTIES OF Sr- AND Mn-DOPED LANTHANUM GALLATE

Synthesis and Characterization of La0.85Sr0.15Ga0.80Mg0.20O2.825 by Glycine Combustion Method and EDTA Combustion Method

Synthesis and Properties of Sr- and Mg-doped LaGaO3 Materials

Preparation and Electrochemical Performance of La-Doped LiMn2-xLaxO4 by Sol-Gel Method

Preparation and Performance of Large-Area La0.9Sr0.1Ga0.8Mg0.2O3−δ Electrolyte for Intermediate Temperature Solid Oxide Fuel Cell

Synthesis and Characterization of La0.85Sr0.15Ga0.85Mg0.15O3−δ Electrolyte by Steric Entrapment Synthesis Method

Preparation and electrochemical characterization of Sr- and Mn-doped LaGaO 3 as anode materials for LSGM-based SOFCs

Preparation and characterization of La0.9Sr0.1 Ga0.8Mg0.2O2.85 oxygen-ion conductor

Research Progress in Preparation Methods of Nanometer La_2O_3 and Its Composite Oxides

Synthesis of La0.9Sr0.1Ga0.8Mg0.2O3-delta Powder by a Two-Step Doping Method

Preparation and Properties of Perovskite La1-xSrxCoO3-delta Powders and Ag-LSCO Electrical Contact Composite Materials

Development of Doped Lanthanum Gallate Solid Electrolytes

Coupling of tape casting and in situ solid-state reaction for manufacturing La0.9Sr0.1Ga0.8Mg0.2O3 electrolyte of efficient solid oxide cells

Progress in LaGaO3-based Oxide Ion Conductor

Preparation and Properties of LSGM (Li/Na)(2)CO3 Composite Electrolytes for LT SOFC

Study on Properties of LSGM Electrolyte Made by Tape Casting Method and Applications in SOFC

Preparation and Conductivity of LSGM-(Li/Na)(2)CO3 Composite Electrolyte