Abstract:A spherical TiCl4/MgCl2-based catalyst was used in the synthesis of in-reactor polyethylene/polypropylene alloys by polyethylene homopolymerization and subsequent homopolymerization of propylene in the gas phase. Different conditions in the ethylene homopolymerization stage, such as monomer pressure and polymerization temperature, were investigated, and their influences on the structure and properties of in-reactor alloys were studied. Raising the polymerization temperature is the most effective way of speeding up polymerization and regulating the ethylene content of polyethylene (PE)/polypropylene (PP) alloys, but it will cause a greater increase in the PE-b-PP block copolymer fraction (named fraction D) than in the fraction of PP-block-PE in which the PP segments have low or medium isotacticity (named fraction A). Although changing ethylene monomer pressure could influence the ethylene content of PE/PP alloys slightly, it is an effective way of regulating the structural distribution. Reducing the monomer pressure will evidently increase fractions A and D. The mechanical properties of the alloys, including impact strength and flexural modulus, can be regulated in a broad range with changes in polymerization conditions. These properties are highly dependent on the amount, distribution, and chain structure of fractions A and D. The impact strength is affected by both fraction A and fraction D in a complicated way, whereas the flexural modulus is mainly determined by the amount of fraction A. (c) 2006 Wiley Periodicals, Inc.

Preparation and Characterization of Spherical PP/PB Alloys with MgCl 2 -Supported Ziegler-Natta Catalyst

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

Preparation of Polypropylene/MMT Nanocomposites Using Complex Supported Catalysts

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

I-Pp/epr REACTOR ALLOY PREPARED THROUGH ETHYLENE/PROPYLENE SLURRY COPOLYMERIZATION CATALYZED BY METALLOCENE SUPPORTED Ipp PARTICLES

PREPARATION OF ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE USING STRUCTURED NANOPARTICAL ZIEGLER-NATTA CATALYSTS

Branched-PE/i-PP reactor blends prepared through ethylene gas-phase polymerization catalyzed by α-diimine nickel supported on iPP particles

High temperature polymerization of propylene catalyzed by MgCl2-supported Ziegler–Natta catalyst with various cocatalysts

Structure and Morphology of Polyethylene/polypropylene In‐reactor Alloys Synthesized by Spherical High‐yield Ziegler–Natta Catalyst

Synthesis of High Quality PE/PP In-Reactor Alloys with PE Matrix by Multi-Stage Polymerization

Preparation of Regular Polyethylene Hollow Spheres with Supported Z-N Catalysts

Chain structure of polyethylene/polypropylene in-reactor alloy synthesized in gas phase with spherical Ziegler–Natta catalyst

Influence of Copolymerization Conditions on the Structure and Properties of Polyethylene/Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloys Synthesized in Gas-Phase with Spherical Ziegler-Natta Catalyst

Study on the microstructures of polypropylene synthesized by a novel MgCl<SUB>2</SUB>-supported and low Ti-loading Ziegler–Natta catalyst

Effects of Doping LiCl into MgCl2-Supported Ziegler−Natta Catalyst on the Molecular Weight Distribution and Isotacticity of Polypropylene

Synthesis of high performance PE/PP/EPR in-reactor alloys by sequential multi-stage gas-phase polymerization with spherical Ziegler-natta catalyst

Microtacticity of Polypropylene Fractions Produced by Different Active Sites of Heterogeneous Ziegler-Natta Catalyst

Influence of Polymerization Conditions on the Structure and Properties of Polyethylene/polypropylene In‐reactor Alloy Synthesized in the Gas Phase with a Spherical Ziegler–Natta Catalyst

Influence of Cocatalyst on High Temperature Polymerization of Propylene Catalyzed by Ziegler-Natta Catalyst

Characterization of isotactic polypropylene prepared with dimethylsilyl bis(1-indenyl)zirconium dichloride supported on methylaluminoxane pretreated silica

Morphology and properties of PP in-reactor alloys prepared with a MgCl2/TiCl4/diisobutyl phthalate/phosphate tris-methylphenyl ester catalyst system