Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Study on High Chromium Cast Iron Fracture Grinding Roll

Fracture Analysis of High Chromium Cast Iron Roll on CSP Mill

Effect of Hot-Rolling Deformation on Microstructure and Sliding Wear of High-Chromium Cast Iron

Abrasive wear behavior and mechanism of high chromium cast iron

A Study On The Dynamic Characteristics Of Abrasion For High-Chromium Alloys

Fracture failure analysis and research on super-large-diameter roll

Cracking in a Fe–25Mn–3Si–3Al Steel

In-Situ Study of High Temperature Tensile Fracture Mechanism of Mar-M247 Alloy

Characterization of Microstructure and Mechanical Properties of High Chromium Cast Irons Using Sem and Nanoindentation

Preparation and Mechanical Properties of High Silicon Molybdenum Cast Iron Materials: Based on Deep Learning Model

Signs of Degradation of Carbide Phases in Chromium-Nickel Cast Iron at the Operating Temperatures of Forming Rolls

Wear Behavior and Microstructure Changes of a High Chromium Cast Iron: The Combined Effect of Heat Treatment and Alloying Elements

Tempering temperature dependence on the microstructure, mechanical properties and wear behaviour of a novel high chromium cast iron

Breakup of Eutectic Carbide Network of White Cast Irons at High Temperatures

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Study on the mechanism of mechanical properties deterioration of brake disc materials of high-speed train

Study on Crack Forming of Centrifugal Cast High Speed Steel Roll

Effect of quenching temperature on microstructure and properties of multivariate high chromium cast iron

Evolution of Surface Crack on Slab During Rough Rolling Using Thermal-Mechanical FEM

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Microstructure and Mechanical Properties of High-Chromium Cast Iron/Low-Carbon Steel Composite Prepared by Hot Rolling Process