Abstract:The aim of this study is to enhance the plasticity and strength of M2 high-speed steel through electron beam melting (EBM) technology. Therefore, by controlling different melting times to change the energy input, a gradient distribution of grain size and uniform distribution of carbides can be achieved. During the deformation process, the gradient structure causes geometrically necessary dislocations (GND) to accumulate near the boundary of regions in the soft zone, resulting in compressive stress in the soft zone and tensile stress in the hard zone, ultimately achieving heterogeneity-induced (HDI) work hardening. This study is to EBM technology for the design and fabrication of three types of M2 high-speed steel samples, denoted as SS-1, SS-2, and SS-3, utilizing three distinct scanning strategies: single melting, double melting, and a combination thereof. The microstructure and phase evolution of these samples were comprehensively characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electron backscatter diffraction (EBSD) techniques. The findings demonstrate that when sample SS-3 was subjected to the combined scanning strategy involving both single melting and double melting approaches, its crystal structure exhibited a gradient distribution along with the presence of back stress during tensile testing. Sample SS-3 achieved an average tensile strength of 1479 MPa with an average elongation rate of 1.8%. This represents an enhancement in average tensile strength by approximately 8.6% compared to sample SS-1 (∼1362 MPa) and a significant increase in average elongation rate by around 20% compared to SS-1 (∼1.44%). The gradient grain structure materials show the microstructure transformation from fine grain to coarse-grain in the same material, thus reducing the stress concentration caused by the change of mechanical properties in each region. The SS-3 sample can maintain significant ductility while improving tensile strength. Consequently, this represents a pivotal direction for the advancement of high-performance structural materials. The conducted experimental studies have demonstrated that geometrically necessary dislocations (GNDs) and their associated strain hardening play a crucial role in enhancing the strength of grain structure materials. Additionally, these are essential to achieve an exceptional synergy between strength and toughness in these materials.

Microstructure and properties of M32 powder metallurgy high speed steel by canned hot extrusion technology

Development of Powder Metallurgy High Speed Steel

Research on annealing process for welded joint of the dissimilar steel——weld property and holding time

Effect of Heat Treatment on Microstructure and Properties of Powder Metallurgy High-Speed Steel Prepared by Hot Isostatic Pressing

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

High-Temperature Annealing Significantly Enhances Intrinsic Hot Workability of the As-cast High-Nitrogen M42 High-Speed Steel

Homogenization Treatment and Plastic Deformation Improve the Carbide Homogeneity of M42 High-Speed Steel

Microstructure Evolution and Precipitation Strengthening Behaviour of Additively Manufactured High-speed Steels

Improvement of mechanical property of M2 high-speed steel with hetero-microstructure tailored via electron beam melting

Microstructural Evolution, Behavior of Precipitates, and Mechanical Properties of Powder Metallurgical High-Speed Steel S390 During Tempering

Effect of Tempering Conditions on Secondary Hardening of Carbides and Retained Austenite in Spray-Formed M42 High-Speed Steel

The effects of extrusion ratio and heat treatment on microstructures and tensile properties of a powder metallurgy Fe–22Mn steel

Superior Mechanical Properties of M35 High-Speed Steel Obtained by Controlling Carbide Precipitation and Distribution Via Electropulsing Treatment

Effect of Heat Treatment on Microstructural Evolution, Mechanical Properties and Tribological Properties of H13 Steel Prepared Using Selective Laser Melting

Mechanical and tribological assessments of high-vanadium high-speed steel by the conventional powder metallurgy process

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Powder Metallurgy Ti-48Al Alloy

Effect of hot stamping and quenching & partitioning process on microstructure and mechanical properties of ultra-high strength steel

Microstructure and Mechanical Properties of B4C-Blended M3:2 High-Speed Steel Powders Consolidated by Sintering and Heat Treatment

Microstructural changes of high speed steel powders during heating in vacuum

Effect of Cycling Heat Treatment on the Microstructure and Properties of H13 Steel Prepared for Hot-Extrusion Die

Microstructural evolution and mechanical properties of an ultrahigh-strength Al−Zn−Mg−Cu alloy via powder metallurgy and hot extrusion