Abstract:This paper presents an ultra-low power incremental ADC for biosensor interface circuits. The ADC consists of a resettable second-order delta-sigma (Delta Sigma) modulator core and a resettable decimation filter. Several techniques are adopted to minimize its power consumption. A feedforward path is introduced to the modulator core to relax the signal swing and linearity requirement of the integrators. A correlated-double-sampling (CDS) technique is applied to reject the offset and 1/f noise, thereby removing the integrator leakage and relaxing the gain requirement of the OTA. A simple double-tailed inverter-based fully differential OTA using a thick-oxide CMOS is proposed to operate in the subthreshold region to fulfill both an ultra-low power and a large output swing at 1.2 V supply. The signal addition before the comparator in the feedforward architecture is performed in the current domain instead of the voltage domain to minimize the capacitive load to the integrators. The capacitors used in this design are of customized metal-oxide-metal (MOM) type to reach the minimum capacitance set by the kT/C noise limit. Fabricated with a 1P6M 0.18 mu m CMOS technology, the presented incremental ADC consumes 600 nW at 2 kS/s from a 1.2 V supply, and achieves 68.3 dB signal to noise and distortion ratio (SNDR) at the Nyquist frequency and an FOM of 0.14 pJ/conversion step. The core area is 100 x 120 mu m(2.)

A I-V 36-pW low-noise adaptive interface IC for portable biomedical applications

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

A Multi-Parameter Bio-Electric ASIC Sensor with Integrated 2-Wire Data Transmission Protocol for Wearable Healthcare System

A low-offset analogue front-end IC for multi-channel physiological signal acquisition

An ASIC Solution for Intelligent Electrodes and Active-Cable Used in a Wearable ECG Monitoring System.

A 1.8-V 770-nW biopotential acquistion system for portable applications

A Low Power Low Noise Analog Front End for Portable Healthcare System

A 0.6V, 8.4uw AFE Circuit for Biomedical Signal Recording

A 1.2 V 600 Nw 12-Bit 2 Ks/s Incremental ADC for Biosensor Application

A 36μw Reconfigurable Analog Front-End IC for Multimodal Vital Signs Monitoring

Design of an Analog Front-End for Ambulatory Biopotential Measurement Systems

A Low-Power Fully Differential Reconfigurable Biomedical Electronics Interface to Detect Heart Signals

A 5.8 nW 9.1-ENOB 1-kS/s Local Asynchronous Successive Approximation Register ADC for Implantable Medical Device

A 0.3V 10b 3MS/s SAR ADC With Comparator Calibration and Kickback Noise Reduction for Biomedical Applications

A 0.6V 1.07 <i>W</i>/Channel neural interface IC using level-shifted feedback

A High DR High-Input-Impedance Programmable-Gain ECG Acquisition Interface with Non-inverting Continuous Time Sigma-Delta Modulator

A 36 Μw 1.1 Mm 2 Reconfigurable Analog Front-End for Cardiovascular and Respiratory Signals Recording

A 1.5 mm2 4-Channel EEG/BIOZ Acquisition ASIC With 15.2-Bit 3-Step ADC Based on a Signal-Dependent Low-Power Strategy

Micro-Power Low-Offset Instrumentation Amplifier IC Design for Biomedical System Applications

A 455 Nw 220 Fj/conversion-Step 12 Bits 2 Ks/s SAR ADC for Portable Biopotential Acquisition Systems

A Gain and Bandwidth Individually Tunable ExG Analog Frontend with 516nV<sub>rms</sub> Noise for Flexible Biomedical Sensors