Abstract:The high brittle-to-ductile transition temperature (DBTT) of tungsten is a significant concern that hinders its use as a structural material. This study employs small punch testing over a broad temperature range to investigate the anisotropic mechanism of DBTT in as-hot rolled W-2%wt Y2O3 specimens. RD-TD specimen exhibits the highest EUS(0.75/J), highest ELS(0.08/J) and lowest TSP (∼336 °C) in three oriented materials. Multiple factors were conducted individually, revealing that the similar dislocation density, and fraction of LAGBs are not the primary determinant of the observed variations in DBTT performance. RD-TD specimen with strong {111}<112> γ-fiber texture exhibits the highest Fm that is nearly twice as high as that of RD-ND specimen and almost three times as high as that of TD-ND specimen. The relationship between the grain morphology, such as aspect ratio present on the DBTT as well as fracture mode of the material is apparent. RD-TD specimen boasts superior plastic properties, which displays an annular crack with the dome-like structure at the core and small incisions at the periphery. While, the plasticity of TD-ND and RD-ND specimens are deemed inadequate, as evidenced by the emergence of multiple lengthy and linear cracks in a particular orientation upon initial cracking. The utilization of numerous superimposed loads and the sandwich configuration of Y2O3 particles in tungsten matrix have been discovered to promote the occurrence of delamination in the thickness direction of the RD-TD specimens. The stratified structure, texture, screw dislocations, and grain aspect ratio have been identified as the pivotal factors influencing the anisotropy on DBTT and fracture analysis.

Ductile to Brittle Transition of Pure Al Sheet Constrained by Parallel Bi-Interface with High Strength Al Alloy

On revealing the mechanisms involved in brittle-to-ductile transition of fracture behaviors for γ-TiAl alloy under dynamic conditions

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Fabrication of Al/Al-TiB 2 laminate composites via hot press sintering process: An insight into the mechanical properties and fracture behavior

Dynamic behavior and fracture mode of TiAl intermetallics with different microstructures at elevated temperatures

Deformation mechanisms and their role in the lack of ductility in the refractory-based high entropy alloy AlMo0.5NbTa0.5TiZr

Achieving room-temperature brittle-to-ductile transition in ultrafine layered Fe-Al alloys

Effects of Al on crack propagation in titanium alloys and the governing toughening mechanism

In-situ investigation on tensile properties of a novel Ti/Al composite sheet

Microstructure and Mechanical Properties of Ti-Al-Ti-Ti2AlNb Laminated Composites Based on the Ductile-brittle Structure

Grain boundary decohesion in body-centered cubic Mg-Li-Al alloys

Brittle-to-ductile transition of Au2Al and AuAl2 intermetallic compounds in wire bonding

Study of the Transition from Strain Localization to Fracture of Ti–6.5Al–3.5Mo–1.5Zr–0.3Si Alloy by Experiments and Phase-Field Modeling

Study of tensile properties and fracture mechanisms of fully lamellar TiAl based alloy

Microstructural morphology effects on fracture toughness and crack growth behaviors in a high strength titanium alloy

Effect of Anisotropic Mechanism of W-2%wt Y2O3 Alloy on DBTT and Fracture Analysis under Small Punch Testing

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

The mechanism for annealing-induced ductile to brittle transition in a high-temperature titanium alloy and its mitigation

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Ductility and Fracture of FeAl: Effects of Composition and Environment

Strengthening and toughening mechanisms of tailored Al/Al-TiB 2 laminated composites fabricated by hot press sintering process