Abstract:Cu/Al composites have the excellent properties of both Cu and Al, and have the properties of light weight and high conductivity, so they have been widely concerned. In this paper, 5-mm-thick Cu/Al composites prepared by the cast-rolling process are used as experimental materials. To reveal the strengthening and toughening mechanisms of the Cu/Al composites, the interfacial structure, micro-morphology, stress-strain condition, and GND distribution of Cu/Al composites before and after deformation were characterized utilizing TEM, TKD, and EBSD. The results show that the submicron intermetallic compounds Al 2 Cu and Al 4 Cu 9 are formed from the casting-rolling Cu/Al composites. After 15% tensile deformation, many gaps occurred in the interface layer, but at the gaps, there was no crack spreading to the Cu and Al layers. Meanwhile, the deformation in different directions occurs in the Cu grains near the interface, forming a dislocation wall, and the entanglement of the dislocation occurs in the Cu layer near the interface, which contributes to the improvement of tensile strength. The Al layer near the interface layer produces kink bands, which helps to improve the ductility of the composites. Besides, due to the action of the hard intermetallic compound layer, with the increase in tensile deformation, a large number of GND are gradually accumulated in the Cu and Al layers near the interface, resulting in remote back stress, which makes the softer Cu and Al layers obtain higher strength. At the same time, the back stress caused by GND will induce strain hardening, which helps to maintain ductility, so that Cu/Al composites have higher plastic deformation ability while improving mechanical properties.

Strengthening and toughening mechanisms of tailored Al/Al-TiB 2 laminated composites fabricated by hot press sintering process

Fabrication of Al/Al-TiB 2 laminate composites via hot press sintering process: An insight into the mechanical properties and fracture behavior

Fabrication of Fully Dense Tial-Based Composite Sheets with A Novel Microlaminated Microstructure

PREPARATION AND PROPERTIES OF TiB2/TiAl COMPOSITE SHEETS WITH LAYERED STRUCTURE

Strengthening and toughening of laminated TiAl composite sheets by titanium alloy layers and carbide particles

Microstructure and Mechanical Properties of Ti-Al-Ti-Ti2AlNb Laminated Composites Based on the Ductile-brittle Structure

Multiplied bending ductility and toughness of titanium matrix composites by laminated structure manipulation

Interface regulation effects on mechanical behavior of heterostructure Ti6Al4V/TiAl-based laminated composite sheets

Microstructures and Mechanical Properties of Laminated Structural Nb-Ti-Al Composites Fabricated by Laser Deposition

Design a novel TiAl/Ti2AlNb laminated composite with high toughness prepared by foil-foil metallurgy

Enhancing strength-ductility synergy in nano-sized TiB 2 /Al composite via rapid solidification and thermo-mechanical processing

Influence of Interface on Mechanical Behavior of Al-B4C/Al Laminated Composites under Quasi-Static and Impact Loading

Balancing the strength and ductility of Ti2AlC/TiAl composite with a bioinspired micro-nano laminated architecture

The Flexural Strength and Fracture Toughness of TC4-Based Laminated Composites Reinforced with Ti Aluminide and Carbide

Fabrication and strengthening mechanism of dual-phased and bimodal-sized (Si3N4p + TiB2p)/6061Al hybrid composite

Extraordinary room temperature tensile ductility of laminated Ti/Al composite: Roles of anisotropy and strain rate sensitivity

In-situ investigation on tensile properties of a novel Ti/Al composite sheet

Design a Ti6Al4Vâ€“Ti43Al9V laminated composite with high strength and fracture toughness

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

In-situ synthesis of Al2O3-reinforced high Nb–TiAl laminated composite with an enhanced strength-toughness performance

Fabrication, microstructure and compressive properties of Ti2AlC/TiAl composite with a bioinspired laminated structure