Abstract:The root mean square (rms) surface roughness extracted from atomic force microscopy is widely employed to complement the characterisation of ion implantation processes in 4H-SiC. It is known that the protection of a carbon film eliminates or mitigates roughening of the SiC surface during postimplantation annealing. This study, based on a rich original data collection of Al+ ion implanted 4H-SiC samples, allows for a quantitative description of the surface morphology as a function of the annealing temperature and time and of the Al implanted concentration. With increasing thermal budget, the evolution from flat, to blurred with ripples, granular, and finally jagged surface, results in a monotonous increase in the root mean square roughness. Additional information is given by the trends of the roughness exponent and of the correlation length, extracted from the height-height correlation function, which account for the surface evolution below 1700°C and for the effect of the Al implanted concentration on the ripple size, respectively. A combination of low roughness parameter and high correlation length identify the transition from ripples to jagged morphology. LAY DESCRIPTION: Selective area doping is a key step in the fabrication of hexagonal Silicon Carbide (4H-SiC) power electronic devices. It is achieved by ion implantation followed by a high temperature postimplantation annealing to restore the lattice and electrically activate the dopants. Aluminium, the preferred p-type dopant, is electrically activated at temperature ranging between 1500°C and 2000°C. The time required to complete the activation process is longer the lower the annealing temperature, spanning between some minutes and hundreds of hours. During annealing, 4H-SiC wafers are encapsulated by a temperature-resistant carbon layer (C-cap) in order to avoid step bunching and reduce surface roughening. Nevertheless, surface modifications can occur at high temperature. For this reason, the characterisations of 4H-SiC doping processes report not only the electrical activation of the dopants, but also the root mean square surface roughness obtained at the end of the process. However, rms values can be scattered because technological parameters such as the heating system and the way to deposit and remove the C-cap can affect the final result as well as the process parameters. Furthermore, the C-cap resistance to long annealing has been proven only by electrical measurements, but the surface morphology has never been observed. This work presents a quantitative characterisation of the surface morphology of Al implanted 4H-SiC as a function of the annealing temperature, time and of the Al implanted concentration, independent of the heating system and of the C-cap technology. The produced sample collection allowed to correlate characteristic surface features with the corresponding quantities extracted from image analysis that can be more sensitive to process parameters than the sole rms. These findings can be used to enrich process optimisation tools.

Influence of surface morphology on the field emission properties of planar SiC/Si heterostructures formed by ion beam synthesis

Electron Field Emission from SiC/Si Heterostructures Formed by Carbon Implantation into Silicon and Etching of the Top Silicon Layer

Electron Field Emission from SiC∕Si Heterostructures by High Temperature Carbon Implantation into Silicon

Surface roughening in ion implanted 4H-silicon carbide

Laser microstructuring of Si surfaces for low-threshold field-electron emission

Formation of CeSi2 on the Si surface upon high current pulsed Ce-ion implantation

Surface and Interface Properties of Ion Implanted 4H-Silicon Carbide

Formation of SiC-surface nanocrystals by ion implantation and electron beam rapid thermal annealing

Evolution of secondary defects in arsenic implanted Si

Atomistic Analysis on Implantation Effects of Hydrogen Ions and Copper Ions into 4H-Sic

Formation of SiC-surface layer by ion implantation

Hrtem Study of SiC Buried Layer Formed by C+implantation in Silicon

4H-SiC surface morphology after Al ion implantation and annealing with C-cap

FORMATION AND CHARACTERIZATION OF 3C-SIC BY CARBON-ION IMPLANTATION INTO SILICON WITH A MEVVA ION SOURCE

Nanoparticle-density-dependent Field Emission of Surface-Decorated SiC Nanowires

Mechanical properties and indentation-induced phase transformation in 4H–SiC implanted by hydrogen ions

Investigation of Exfoliation Efficiency of 6H-SiC Implanted Sequentially with He+ and H2+ Ions

Formation of the Ersi2 Phase and the Associated Fractal Pattern on the Si Surface Upon High Current Er-Ion Implantation

Lattice Defects and Exfoliation Efficiency of 6H-SiC via H2+ Implantation at Elevated Temperature

Influence of a thin amorphous surface layer on de-channeling during aluminum implantation at different temperatures into 4H-SiC

Simultaneous formation of SiC and Si nanostructures on silicon by local ion implantation and electron beam annealing