Abstract:Al-SiCw composites can be readily shaped with conventional secondary metalworking techniques. During such forming operations, Al-SiCw composites may experience appreciable amounts of cold work, which may both influence their further forming operations and degrade some mechanical properties. Therefore, after forming operations it may be necessary to anneal the composites. Mostly, recrystallization annealing is used to achieve this purpose. The purpose of this study is to give useful information on thermomechanical processing of Al-SiCw composites by investigating their recrystallization kinetics. Al/SiC/15w composites are fabricated through a squeeze casting route followed by a hot extrusion at an extrusion ratio of 18: 1, and cold-rolled to 30, 50, and 70% of the original thickness, respectively. Then as-cold-rolled Al/SiC/15w composites are heated either continuously or isothermally to make the composites recrystallize. To investigate the kinetics of the cold-rolled composites during heating, differential thermal analysis (DTA) and hardness testing are carried out. It is found that the recrystallization kinetics of Al/SiC/15w composites is strongly dependent on deformation degree. When the reduction in thickness is less than 50%, with the increase in reduction in thickness, a faster kinetics of recovery and recrystallization occur. When the reduction in thickness is more than 50%, however, with the increase in reduction in thickness, only a faster kinetics of recovery occurs and the kinetics of recrystallization is nearly not influenced. Whiskers play a role in promoting the kinetics of recrystallization by particle-stimulated nucleation (PSN). While solute atoms make the kinetics of recrystallization largely delayed, precipitates only slightly slow down the recrystallization kinetics. At 280°C, between 100 and 200 s, extended recovery reaction and recrystallization nucleation are dominant. After 200 s, however, the growth of recrystallized grains becomes a dominant softening mechanism. As a result of the recrystallization taking place before aging, aging kinetics of the cold-rolled solution-treated 6061Al-SiCw composite is delayed.

Recrystallisation Kinetics of Aluminium AA1200 Cold Rolled to True Strain of 2

Nanostructured Aluminium - Recovery And Recrystallization

Recovery and Recrystallization in Commercial Purity Aluminum Cold Rolled to an Ultrahigh Strain

On the Relationship between Thermomechanical Processing Parameters and Recrystallization Texture in AA1100 Aluminum Alloy

Annealing Behavior of Nanostructured Aluminum Produced by Cold Rolling to Ultrahigh Strains

Study of the recrystallization behaviour of the aluminium 1565ch alloy during hot rolling of the as cast structures

Thermal Stability of Aluminum Cold Rolled to Large Strain

Recrystallization Kinetics of Cold-Rolled Squeeze-Cast Al/Sic/15w Composites

Evolution of Microstructure and Texture During Recovery and Recrystallization in Heavily Rolled Aluminum

Deformation and Recrystallization Textures in Straight-Rolled and Pseudo Cross-Rolled AA 3105 Aluminum Alloy

Recrystallization behavior of pure tungsten hot-rolled with high accumulated strain during annealing at 1250 C-1350 C

Dynamic recrystallization mechanism during warm deformation in 1420 alloy

Evaluation of static recrystallization and grain growth kinetics of hot-rolled AZ31 alloy

In-Situ Observations of Migration of Recrystallization Boundaries in Pure Aluminium

Recrystallization Behavior of a Two-Way Cold Rolled 12cr ODS Steel

Recrystallization Texture Evolution of Cold-Rolled Cu Foils Governed by Microstructural and Sample Geometrical Factors During Heating

Recovery and Recrystallization as a Function of Deformed Microstructure Orientation in Coarse Grained Cold-Rolled Ni

Interactions between precipitation and recrystallisation in an Al–Mg–Si alloy

Recrystallization behavior and texture evolution during annealing of cryogenic-rolled 3003 aluminum alloy

Effect of grain size on the recrystallization kinetics and crystallographic texture of unidirectionally rolled Ti-15V-3Cr-3Al-3Sn alloy

Effect of second-phase precipitates on deformation microstructure in AA2024 (Al–Cu–Mg): dislocation substructures and stored energy