Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

A Modified Polymethylsilane As the Precursor for Ceramic Matrix Composites

Evaluation of Poly(methylsilane‐carbosilane) Synthesized from Methyl‐dichlorosilane and Chloromethyldichloromethylsilane As a Precursor for SiC

A New SiC Precursor with High Ceramic Yield: Synthesis and Characterization of CHxMeSiH2‐containing Poly(methylsilane‐carbosilane)

Preceramic Polymer As Precursor for Near‐stoichiometric Silicon Carbon with High Ceramic Yield

Preparation and Formation Mechanism of C/C–SiC Composites Using Polymer-Si Slurry Reactive Melt Infiltration

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

C/C–SiC Composites Derived from Single‐source Poly(silylene–acetylene) Precursors

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

A linear polycarbosilane containing <i>m</i>-carborane units: Synthesis and characterization as precursor for SiC/B<sub>4</sub>C ceramics

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Polymethylsilane As A Precursor to High-Purity Silicon-Carbide

A linear polycarbosilane containing m-carborane units: Synthesis and characterization as precursor for SiC/B4C ceramics

Synthesis of cyano-polycarbosilane and investigation of its pyrolysis process

Preceramic Paper-Derived SiCf/SiCp Composites Obtained by Spark Plasma Sintering: Processing, Microstructure and Mechanical Properties

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Preparation and Stereolithography of SiC Ceramic Precursor with High Photosensitivity and Ceramic Yield

Superparamagnetic Silicon Carbonitride Ceramic Fibers Through In Situ Generation of Iron Silicide Nanoparticles During Pyrolysis of an Iron-Modified Polysilazane

Synthesis, Characterization and Oxidation Behavior of A Novel Curable Liquid Polysilane Precursors for C/C-Sic Composite

Preparation and properties of Ti3SiC2 preform reinforced SiC ceramic matrix composites

Additive manufacturing of polymer‐derived ceramic matrix composites

C/C-Sic Composite Fabricated Via Pcs-Si Slurry Reactive Melt Infiltration