Abstract:Selective laser reaction sintering techniques (SLRS) techniques were investigated for the production of near net-shape non-oxide ceramics including SiC, Si3N4, and HfC/SiC composites that might be compatible with prevailing powder bed fusion additive manufacturing processes. Reaction bonded layers of covalent ceramics were produced using in-situ reactions that occur during selective laser processing and layer formation. During SLRS, precursor materials composed of metal and/or metal oxide powders were fashioned into powder beds for conversion to non-oxide ceramic layers. Laser-processing was used to initiate simultaneous chemical conversion and local interparticle bonding of precursor particles in 100 vol% CH4 or NH3 gases. Several factors related to the reaction synthesis process—precursor chemistry, gas-solid and gas-liquid synthesis mechanisms, precursor vapor pressures—were investigated in relation to resulting microstructures and non-oxide yields. Results indicated that the volumetric changes which occurred during in-situ conversion of single component precursors negatively impacted the surface layer microstructure. To circumvent the internal stresses and cracking that accompanied the conversion of Si or Hf (that expands upon conversion) or SiOx (that contracts during conversion), optimized ratios of the precursor constituents were used to produce near isovolumetric conversion to the product phase. Phase characterization indicated that precipitation of SiC from the Si/SiO2 melt formed continuous, crack-free, and dense layers of 93.7 wt% SiC that were approximately 35 µm thick, while sintered HfC/SiC composites (84.2 wt% yield) were produced from the laser-processing of Hf/SiO2 in CH4. By contrast, the SLRS of Si/SiOx precursor materials used to produce Si3N4 resulted in whisker formation and materials vaporization due to the high temperatures required for conversion. The results demonstrate that under appropriate processing conditions and precursor selection, the formation of near net-shape SiC and SiC composites might be achieved through single-step AM-compatible techniques.

Influence of Silicon Carbide on Direct Powder Bed Selective Laser Process (Sintering/Melting) of Alumina

Process Optimization of SiC-Reinforced Aluminum Matrix Composites Prepared Using Laser Powder Bed Fusion and the Effect of Particle Morphology on Performance

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Selective laser sintering of porous Al2O3-based ceramics using both Al2O3 and SiO2 poly-hollow microspheres as raw materials

Selective Laser Reaction Synthesis of SiC, Si$_3$N$_4$ and HfC/SiC Composites for Additive Manufacturing

Selective laser reaction synthesis of SiC, Si3N4 and HfC/SiC composites for additive manufacturing

Investigation of curing behavior and mechanical properties of SiC ceramics prepared by vat photopolymerization combined with pressureless liquid-phase sintering using Al 2 O 3 -coated SiC powder

Single-step additive manufacturing of silicon carbide through laser-induced phase separation

Laser Powder Bed Fusion of Oxidized Microscale SiC-particle-reinforced AlSi10Mg Matrix Composites: Microstructure, Porosity, and Mechanical Properties

Preparation of silicon carbide ceramic slurry for stereolithography based additive manufacturing

Structure and Properties of Spark Plasma Sintered SiC Ceramics with Oxide Additives

Properties regulation of SiC ceramics prepared via stereolithography combined with reactive melt infiltration techniques

Selective laser sintering of Si3N4 and Al 2O3 ceramic powders

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Silicon carbide ceramics manufactured by digital light processing and low temperature sintering

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Performance optimization of Si/SiC ceramic triply periodic minimal surface structures via laser powder bed fusion

Fabrication and characterization of SiC/Al composites prepared by laser powder bed fusion (LPBF) combined with vacuum pressure infiltration