Abstract:A novel microfluidic picoliter-scale sample introduction approach was developed by combining the spontaneous injection approach with a capillary electrophoresis (CE) system based on a short capillary and slotted-vial array. A droplet splitting phenomenon at the capillary inlet end during the spontaneous sample introduction process was observed for the first time. On the basis of this phenomenon, a translational spontaneous injection approach was established to reduce sample injection volumes to the sub-100 pL range. A versatile high-speed capillary electrophoresis (HSCE) system was built on the basis of this sample injection approach with separation performance comparable to or even better than those reported in microfluidic chip-based CE systems. The HSCE system was composed of a short fused-silica capillary and an automated sample introduction system with slotted sample and buffer reservoirs and a computer-programmed translational stage. The translational spontaneous sample injection was performed by linearly moving the stage, allowing the capillary inlet first to enter the sample solution and then removing it. A droplet was left at the tip end and spontaneously drawn into the capillary by surface tension effect to achieve sample injection. The stage was continuously moved to allow the capillary inlet to be immersed into the buffer solution, and CE separation was performed by applying a high voltage between the buffer and waste reservoirs. With the use of the novel system, high-speed and efficient capillary zone electrophoresis (CZE) separation of a mixture of five fluorescein isothiocyanate (FITC) labeled amino acids was achieved within 5.4 s in a short capillary with a separation length of 15 mm, reaching separation efficiencies up to 0.40 microm plate height. Outstanding peak height precisions ranging from 1.2% to 3.7% RSD were achieved in 51 consecutive separations. By extension of the separation length to 50 mm, both high-speed and high-resolution CZE separation of eight FITC-labeled amino acids could be obtained in less than 21 s with theoretical plates ranging from 163,000 to 251,000 (corresponding to 0.31-0.20 microm plate heights). The present HSCE system also allowed fast chiral separations of FITC-labeled amino acids under micellar electrokinetic chromatography (MEKC) mode within 6.5 s.

Sample Introduction Techniques For Microfluidic Chip-Based Capillary Electrophoresis

A High-Throughput Continuous Sample Introduction Interface for Microfluidic Chip-Based Capillary Electrophoresis Systems.

An Automated Electrokinetic Continuous Sample Introduction System for Microfluidic Chip-Based Capillary Electrophoresis

Fast and simple sample introduction for capillary electrophoresis microsystems.

[Developments of High-Throughput Microfluidic Sample Introduction Techniques].

Sequential injection sample introduction microfluidic-chip based capillary electrophoresis system

Microfabrication of Integrated Capillary Electrophoresis Chips and On-chip Sample Injection and Separation

High-Throughput Microfluidic Sample Introduction In The Nanoliter To Picoliter Range

Development of a Low-Cost Microfluidic Capillary-Electrophoresis System Coupled with Flow-Injection and Sequential-Injection Sample Introduction (Review).

Falling-Drop Interface for Continuous Sample Introduction in Microfluidic Chips

Progress of Short Capillary-Based High Speed Capillary Electrophoresis Systems

A Pressure-Driven Capillary Electrophoretic System with Injection Valve Sampling.

Microfluidic chip electrophoresis for biochemical analysis

Microfluidic Analysis System Based On Capillary Electrophoresis Chip

Microfluidic chip-based flow-injection analysis with high throughput sampling interface

A microfluidic system for introduction of nanolitre sample in inductively coupled plasma mass spectrometry using electrokinetic flow combined with hydrodynamic flow

Microfluidic Picoliter-Scale Translational Spontaneous Sample Introduction for High-Speed Capillary Electrophoresis

Negative Pressure Pinched Sample Injection for Microchip-Based Electrophoresis.

Fabrication of a Monolithic Sampling Probe System for Automated and Continuous Sample Introduction in Microchip‐based CE

Design and Testing of Micro Fluidic Chemical Analysis Chip Integrated with Micro Valveless Pump

The Development of A Compact Microfluidic Chip Analyzer with Continuous Sample Introduction