Abstract:A novel microfluidic picoliter-scale sample introduction approach was developed by combining the spontaneous injection approach with a capillary electrophoresis (CE) system based on a short capillary and slotted-vial array. A droplet splitting phenomenon at the capillary inlet end during the spontaneous sample introduction process was observed for the first time. On the basis of this phenomenon, a translational spontaneous injection approach was established to reduce sample injection volumes to the sub-100 pL range. A versatile high-speed capillary electrophoresis (HSCE) system was built on the basis of this sample injection approach with separation performance comparable to or even better than those reported in microfluidic chip-based CE systems. The HSCE system was composed of a short fused-silica capillary and an automated sample introduction system with slotted sample and buffer reservoirs and a computer-programmed translational stage. The translational spontaneous sample injection was performed by linearly moving the stage, allowing the capillary inlet first to enter the sample solution and then removing it. A droplet was left at the tip end and spontaneously drawn into the capillary by surface tension effect to achieve sample injection. The stage was continuously moved to allow the capillary inlet to be immersed into the buffer solution, and CE separation was performed by applying a high voltage between the buffer and waste reservoirs. With the use of the novel system, high-speed and efficient capillary zone electrophoresis (CZE) separation of a mixture of five fluorescein isothiocyanate (FITC) labeled amino acids was achieved within 5.4 s in a short capillary with a separation length of 15 mm, reaching separation efficiencies up to 0.40 microm plate height. Outstanding peak height precisions ranging from 1.2% to 3.7% RSD were achieved in 51 consecutive separations. By extension of the separation length to 50 mm, both high-speed and high-resolution CZE separation of eight FITC-labeled amino acids could be obtained in less than 21 s with theoretical plates ranging from 163,000 to 251,000 (corresponding to 0.31-0.20 microm plate heights). The present HSCE system also allowed fast chiral separations of FITC-labeled amino acids under micellar electrokinetic chromatography (MEKC) mode within 6.5 s.

Negative Pressure Pinched Sample Injection for Microchip-Based Electrophoresis.

A Pressure-Driven Capillary Electrophoretic System with Injection Valve Sampling.

Improved hydrostatic pressure sample injection by tilting the microchip towards the disposable miniaturized CE device.

Sequential injection sample introduction microfluidic-chip based capillary electrophoresis system

An Automated Electrokinetic Continuous Sample Introduction System for Microfluidic Chip-Based Capillary Electrophoresis

Microfluidic Picoliter-Scale Translational Spontaneous Sample Introduction for High-Speed Capillary Electrophoresis

Microfabrication of Integrated Capillary Electrophoresis Chips and On-chip Sample Injection and Separation

A High-Throughput Continuous Sample Introduction Interface for Microfluidic Chip-Based Capillary Electrophoresis Systems.

Flow Stabilizer on a Syringe Tip for Hand-Powered Microfluidic Sample Injection

Elimination of suction effect in interfacing microchip electrophoresis with inductively coupled plasma mass spectrometry using porous monolithic plugs.

Fast and simple sample introduction for capillary electrophoresis microsystems.

Pump-free and low-cost negative pressure sampling device for rapid sample loading in MCE.

Rapid and Efficient Isotachophoretic Preconcentration in Free Solution Coupled with Gel Electrophoresis Separation on a Microchip Using a Negative Pressure Sampling Technique.

Accurate And Highly Reproducible Picoliter Injection System For Capillary Electrophoresis

Acupuncture injection for field amplified sample stacking and glass microchip-based capillary gel electrophoresis

A microfluidic system for introduction of nanolitre sample in inductively coupled plasma mass spectrometry using electrokinetic flow combined with hydrodynamic flow

Improvements on the electrokinetic injection technique for microfluidic chips

Fabrication of a Monolithic Sampling Probe System for Automated and Continuous Sample Introduction in Microchip‐based CE

A flexible sample introduction method for polymer microfluidic chips using a push/pull pressure pump.

A Micro Electrophoresis System Based On A Short Capillary Combined With Hydrostatic Pressure Driven Injection And Assisted Separation

Improving hydrodynamic injection in capillary electrophoresis by using the integral of pressure