Abstract:Adiabatic shear band (ASB), a typical failure mechanism in a metal at high strain rates, is hardly controllable or predictable to some extent. The development of the microstructure plays a crucial role in its formation. In this paper, the effect of strain rate on the development of microstructure in ASB of titanium alloy TC4 is investigated using hat-shaped specimens with the split-Hopkinson pressure bar device. The results show that the fracture strength of TC4 is significantly dependent on the shear strain rate. The increase in fracture strength from a strain rate of 11,300 s −1 to 24,930 s −1 is much higher than that from 24,930 s −1 to 35,620 s −1 , which can be attributed to the effect of strain rate on dislocation evolution. Microstructures in both as-received and deformed states are investigated using various characterization techniques such as electron backscatter diffraction and X-ray diffraction. The region of ASB clearly shows three different microstructural features: random distribution of coarse grains (as received), distribution of elongated grains (transition zone), and distribution of equiaxed nanocrystals (shear-localized zone). The width of ASB increases with the strain rate. The possible reason for this is that the higher the strain rate, the larger the region where dynamic recrystallization (DRX) occurs due to the accumulation of a large number of dislocations. In the middle of ASB, a significant decrease in low-angle grain boundaries (LAGBs) and a large increase in high-angle grain boundaries are observed. The texture of specimens, especially the {11–20} and {10–10} planes, changes significantly during shear deformation at high strain rates. The mechanism of continuous dynamic recrystallization can well explain the formation and evolution of DRX within the ASB.

Predeformation Effects on Shear Response and Microstructure in Pure Titanium-TA2

Adiabatic shear instability in a titanium alloy: Extreme deformation-induced phase transformation, nanotwinning, and grain refinement

The Effects of Microstructure on the Dynamic Mechanical Response and Adiabatic Shearing Behaviors of a Near-α Ti-6Al-3Nb-2Zr-1Mo Alloy

Study on High-Temperature Flow Behavior and Substructure and Texture Evolution of TA15 Titanium Alloy

Effect of High Strain Rate on Adiabatic Shearing of α+β Dual-Phase Ti Alloy

Influence of Initial Textures on Microstructure and Mechanical Properties of Commercially Pure TA2 Titanium Sheet Pre-Strained by Cryorolling

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Shear Texture Formation during High-Strain Torsion of Titanium Aluminides

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Multiple Deformation Mechanisms in Adiabatic Shear Bands of a Titanium Alloy during High Strain Rate Deformation

Evolution of microstructure, macrotexture and mechanical properties of high strength biomedical TA4 pure titanium during multi-pass ECAP

In Situ Electron Backscatter Diffraction Study of Deformation Inhomogeneity under Uniaxial Tension of Laser Melting Deposited TA15 Alloy

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

The High-Temperature Deformation Behavior of As-Cast Ti90 Titanium Alloy

Effects of Strain and Strain Rates on Microstructure Evolution Within ASB of TC4

Mechanical Response and Deformation Mechanisms of TB17 Titanium Alloy at High Strain Rates

Deformation Behavior and Tensile Properties of the Semi-Equiaxed Microstructure in Near Alpha Titanium Alloy

Shear localization behavior in hat-shaped specimen of near-α Ti−6Al−2Zr−1Mo−1V titanium alloy loaded at high strain rate

Ex-situ study on mechanical properties and deformation mechanism of three typical microstructures in TA19 titanium alloy

Transmission Electron Microscopy Investigation of Ti2Al Precipitation in Titanium Aluminides During High-Strain Torsion