Abstract:In this study, the texture formation mechanism of a TA15 titanium alloy under different plane strain compression conditions was investigated by analyzing the slipping, dynamic recrystallization (DRX) and phase transformation behaviors. The results indicated that the basal texture component basically appears under all conditions, since the dominant basal slip makes the C-axis of the α grain rotate to the normal direction (ND, i.e., compression direction), but it has a different degree of deflection. With an increase in deformation amount, temperature or strain rate, {0001} poles first approach the ND and then deviate from it. Such deviation is mainly caused by a change in slip behaviors and phase transformation. At a smaller deformation amount and higher strain rate, inhomogeneous deformation easily causes a basal slip preferentially arising from the grain with a soft orientation, resulting in a weak basal texture component. A greater deformation amount can increase the principal strain ratio, thereby promoting other slip systems to be activated, and a lower temperature can increase the critical shear stress of the basal slip, further causing a dispersive orientation under these conditions. At a higher temperature and a lower strain rate, apparent phase transformation will induce the occurrence of lamellar α whose orientation obeys the Burgers orientation of the β phase, thereby disturbing and weakening the deformation texture. As for DRX, continuous-type (CDRX) is most common under most conditions, whereas CDRX grains have a similar orientation to deformed grains, so DRX has little effect on overall texture. Moreover, the microhardness of samples is basically inversely proportional to the grain size, and it can be significantly improved as lamellar α occurs. In addition, deformed samples with a weaker texture present a higher microhardness due to the smaller Schmidt factors of the activated prism slip at ambient loading.

Shear Texture Formation during High-Strain Torsion of Titanium Aluminides

High strain torsion of a TiAl-based alloy

Transmission Electron Microscopy Investigation of Ti2Al Precipitation in Titanium Aluminides During High-Strain Torsion

Constitutive Model and Microstructure Evolution of a Novel TG6 High-Temperature Titanium Alloy during Hot Deformation

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Microstructural Development, Deformation Behavior, and Texture Evolution Investigation during Hot Compression of a Dynamically Recrystallized Ti-5Cu Alloy in the Dual (α + β) Phase Region

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Adiabatic shear instability in a titanium alloy: Extreme deformation-induced phase transformation, nanotwinning, and grain refinement

Study on High-Temperature Flow Behavior and Substructure and Texture Evolution of TA15 Titanium Alloy

Microstructural evolution and FCC twinning behavior during hot deformation of high temperature titanium alloy Ti65

The Role of Deformation and Microstructure Evolution on Texture Formation of a TA15 Alloy Subjected to Plane Strain Compression

Textures of Rectangular Extrusions and Their Effects on the Mechanical Properties of Thermo-Mechanically Treated, Lamellar Microstructure, Ti–47Al–2Cr–2Nb–0.15B

Three-Dimensional In Situ Texture Development and Plasticity Accumulation in the Cyclic Loading of an alpha-Ti Alloy

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments

Mechanism of Crystallographic Orientation and Texture Evolution of Ti60 Alloy during Plane Strain Compression

In-situ synchrotron high energy X-ray diffraction study on the deformation mechanisms of D0 19 -α 2 phase during high-temperature compression in a TiAl alloy

On the thermal evolution of high-pressure torsion processed titanium aluminide

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

The High-Temperature Deformation Behavior of As-Cast Ti90 Titanium Alloy

Microstructural Evolution of Metastable Austenitic Steel During High-Pressure Torsion and Subsequent Heat Treatment