Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Deposition of Carbon Nanofibers on a Low Carbon Steel Substrate Using an Oxy-Acetylene Reducing Flame

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Fabrication and characterization of C3N4 coating by electrochemical deposition on stainless steel

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Super-Low Friction Nickel Based Carbon Nanotube Composite Coating Electro-Deposited from Eutectic Solvents

Deposition of Nanocrystalline Cnx Thin Films on Co/Ni-Covered Substrate by Nitrogen-Atom-Beam-Assisted Pulsed Laser Ablation

Microstructure and mechanical properties of carbon fibers strengthened Ni-based coatings by laser cladding: The effect of carbon fiber contents

Oxidation Behavior of Arc-Sprayed FeMnCrAl/Cr3C2–Ni9Al Coatings Deposited on Low-Carbon Steel Substrates

Structure and properties of nickel-plated CNTs/Fe-based amorphous composite coatings fabricated by high-speed laser cladding

Study on Microstructure and Properties of FeNiCr/Ni Coated Cr_3C_2 Coatings Deposited by High Velocity Arc Spraying

EXPERIMENTAL RESEARCH ON SYNTHESIS OF CARBON NANOTUBES

Preparation and characterisation of the Ni-C composite coating electrodeposited with carbon sol

Preparation of High Purity Carbon Nano -Tubes from Ethylene Decomposition over Nanosized Iron- Based Catalysts

Preparation and Characterization of Sol–gel Al2O3/Ni–P Composite Coatings on Carbon Steel

Interfacial Improvement of Carbon Fiber/epoxy Composites Using a Simple Process for Depositing Commercially Functionalized Carbon Nanotubes on the Fibers

Cn(X) Films Deposited By Laser-Ablation Of Graphite Under Low-Energy Nitrogen-Ion Beam Bombardment

Microstructure and Wear Property of Carbon Nanotube Carburizing Carbon Steel by Laser Surface Remelting

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Acid treatment of carbon nanofibres with encapsulated catalytic iron nanoparticles

Study on superhydrophobicity and excellent corrosion resistance of a novel Ni‐SiC nanocomposite coating