Abstract:Abstract Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding, but the crack sensitivity would be increase due to the higher strength and hardness, which reduced the wear resistance of Ni-based alloys. In this paper, Ni-based coatings with the addition of a plastic phase (an austenitic stainless net) were prepared using laser cladding technology, and the CeO 2 was added in cladding layers. The cracking mechanism, microhardness, microstructure, phase composition, and wear properties were investigated. The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechanics and thermal elastic fracture mechanics. The fracture criterion of the nickel-based coating was obtained, and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficient Δ α . Thus, a new method was proposed, which the stainless steel nets were prefabricated on the substrate. It was found that the number of cracks reduced significantly with the addition of stainless steel net. When the stainless steel net with 14 mesh was added in Ni-based coatings, the average microhardness of nickel composite coating was 565 HV 0.2 , which was 2.6 times higher than that of the 45 steel substrate. Although the rare earth oxide 4 wt.% CeO 2 and stainless steel net were added in the Ni-based coating reducing the microhardness (the average microhardness is 425 HV 0.2 ), the wear resistance of it improved substantially. The wear volume of Ni-based composite coating was 0.56×10 −5 mm 3 ·N −1 ·m −1 , which was 85.1% lower than that of 45 steel. The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.% CeO 2 . This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding.

Structure and properties of nickel-plated CNTs/Fe-based amorphous composite coatings fabricated by high-speed laser cladding

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Microstructure and wear behavior of laser clad interstitial CoCrFeNi high entropy alloy coating reinforced by carbon nanotubes

A Comparative Study of the Microstructure, Mechanical Properties and Corrosion Resistance of Ni- or Fe- Based Composite Coatings by Laser Cladding

Microstructure and Wear Property of Graphene Nanoplatelets Reinforced Nickel-Based Composite Coating by Laser Cladding

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Study of Fe-Ni(Cr) Alloy and Nano-Al2o3 Particles Composite Coating Prepared by Laser Cladding

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Experimental Study of the Microstructure and Micromechanical Properties of Laser Cladded Ni-based Amorphous Composite Coatings

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Microstructure and tribological properties of laser cladded self-lubricating nickel-base composite coatings containing nano-Cu and h-BN solid lubricants

Microstructure and performance of (CoCrNi) 88 Al 6 Ti 6 -cBN composite coatings by high-speed laser cladding (HSLC): A novel strategy for synergizing wear-resistance and friction reduction

Friction and wear behavior of Ni-based carbon nanotubes composite coatings

Preparation and Self-Lubricity Investigation of CNTs/Ni Composite Coatings under Severe Conditions

Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites

Study on microstructure and properties of Fe-based amorphous composite coating by high-speed laser cladding

Friction Properties of Cr_3C_2-Ni Coatings Prepared by Laser Cladding

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Mechanical and Tribological Properties of Fe- and Ni-based Coating Material under Laser Cladding Process