Abstract:Currently, porous SiC ceramics have been a focus of interesting research in the field of porous materials due to their excellent structural properties, high strength, high hardness, and superb mechanical and chemical stabilities even at high temperatures and hostile atmospheres. Porous SiC ceramics have been considered as suitable candidate materials for catalyst supports [1-2], hot gas or molten metal filters [3], high temperature membrane reactors [4], thermal insulating materials [5], gas sensors [6] etc. Porous SiC ceramics are fabricated by various methods including partial sintering [7], carbothermal reduction [8-9], replication or pyrolysis of polymeric sponge [10-12], reaction bonding [13] etc. In all these methods SiC needs to be sintered which requires a very high temperature due to the strong covalent nature of the Si-C bond, selective sintering additives, expensive atmosphere, costly and delicate instrumentation. Processing of porous SiC ceramics at low temperature using a simple technique thus becomes necessary. Bonding of SiC can be done at low temperatures by use of different oxide and non-oxide secondary phases. They include silica, mullite, cordierite, silicon nitride, etc. Various sintering additives are used for the formation of variety of secondary oxide bond phases for formations for porous SiC [14-19] Choice of mullite as a bond for SiC has many advantages. Mullite possesses a high melting point (T m = 1850°C) and a low oxygen diffusion coefficient (5.6 x 10 -14 m 2 /sec at 50°C). It has a matching thermal expansion coefficient with SiC (CTE mullite = 5.3 ×10 -6 /K; CTE SiC = 4.7 ×10 -6 /K at RT-1000 °C) and a high strength that can be retained up to a very high temperature. Different sources of aluminum, such as Al 2 O 3 , Al, AlN, and Al (OH) 3 powders were used for the formation of mullite bonded porous SiC ceramics (MBSC) [20-21]. However, the mullitization temperature of 1550 o C is still necessary. In this work, mullite bonded porous SiC ceramics were fabricated by an in situ reaction-bonding process; the mixture of clay and CaCO 3 were chosen as sintering additives to lower the mullitization reaction between Al 2 O 3 and oxidation-derived SiO 2. The effect amount of alumina, sintering temperature and other sintering aids on material property such as porosity/pore size distribution mechanical and micro structural properties of porous oxide bonded SiC ceramics were studied.

Effect of Sic on Microstructures and Properties of Cordierite-Mullite Multiphase Ceramics Material

The Effects of Mineral Composition and Sintering Temperature on Synthetic Mullite

Fabrication and Properties of Porous Sic-Cordierite Ceramics

Fabrication and Properties of Cordierite–mullite Bonded Porous SiC Ceramics

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

Effect of Cerium Addition on Phase Transformation and Microstructure of Cordierite Ceramics Prepared by Sol-Gel Method

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

The Effect of SiC Whisker on the Sintering and Thermal Shock Resistance Property of ZrO2-mullite Ceramic

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Effect of pore structure evolution on mechanical properties and thermal conductivity of porous SiC-Mullite ceramics

Effect of B2O3 Addition on Low-temperature Sintering Behavior and Properties of SiC/h-BN Multiphase Ceramics

The Effect of Bond Phase Additive and Sintering Temperature on the Properties of Mullite Bonded Porous SiC Ceramics

Fabrication and Properties of SiC/mullite Composite Porous Ceramics

Effects of Y₂O₃ Additive on Mechanical and Thermal Properties of Cordierite-Mullite Ceramics

Effect of Micro SiC Addition on the Microstructure and Thermal Shock Resistance of 3D Printed Mullite Contained Ceramics

Effect of the SiC powder microscopic morphology on properties of Si/SiC ceramics prepared by spark plasma sintering

Effect of Activator on Properties of SiC Porous Ceramics

Effect of Al2O3 + 4sio2 Additives on Sintering Behavior and Thermal Shock Resistance of MgO-Based Ceramics

Influence of La3+, Ce4+ on phase transition and sintering property of cordierite material prepared by solid reaction