Abstract:Molybdenum is used as back contact layer in I-III-VI2 compound thin-film solar cells. Mo film was sputter deposited on 125-mm-diameter Si wafer having 100 orientation using dc magnetron sputtering. Films with similar parameters were also deposited on 2.5cm×10cm soda-lime glass for studying the adhesion to the substrate and chemical reactivity of molybdenum with H2S gas at 475°C for 20min. Mo being refractory material develops stresses. It is essential to deposit stress-free and relatively inert Mo films in order to achieve well adherent and highly efficient CuIn1−xGaxS2 absorber thin film solar cells on flexible metallic foil and glass substrates. Earlier studies have shown that films deposited at sputtering power of 300W and 0.3×10−3Torr working argon pressure develop compressive stress, while the films deposited at 200W and 5×10−3Torr pressure develop tensile stress. Four sets of experiments were carried out to achieve optimum deposition cycle to deposit stress-free Mo. In the first experiment, Mo thickness of 138nm was deposited at 300W power and 0.3×10−3Torr pressure. In the second experiment Mo thickness of 127nm was deposited at power of 200W and pressure of 5×10−3Torr. Two more experiments were carried out by using alternate layers to reduce the overall stress. In a third experiment, two high power cycles were sandwiched between three low power cycles with total film thickness of 330nm. In a fourth experiment two low power cycles were sandwiched between three high power cycles resulting in effective thickness of 315nm. This article describes the wafer bending analysis for stress measurement, x-ray diffraction for crystal quality, scanning electron microscopy for surface morphology and Auger electron spectroscopy for the extent of sulfur diffusion in Mo layer.

Study on Electric Resistivity of Thin Film Materials for GIGS Solar Cell

Investigation in Feasibility of Molybdenum As A Back Contact Layer for Silicon Based Quantum Dot Solar Cells

Influence of contact characteristics of SnO2/P on fill factor of solar cell

Research of CIGS Thin Films on Glass Substrates by RF Magnetron Sputtering

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

Molybdenum Thin Films Fabricated by Rf and Dc Sputtering for Cu(In,Ga)Se-2 Solar Cell Applications

High-energy sputtering to deposit conductive and adherent single Molybdenum layer for solar cell applications

Study of molybdenum back contact layer to achieve adherent and efficient CIGS2 absorber thin-film solar cells

Effect of ZnO buffer layer on AZO film properties and photovoltaic applications

Zinc sulfide thin films deposited by chemical bath: Tuning consideration of structural, optical band gap, and electrical properties for CIGS solar cells application

Improving the efficiency of copper indium gallium (Di-)selenide (CIGS) solar cells through integration of a moth-eye textured resist with a refractive index similar to aluminum doped zinc oxide

Study of the Thin Film Solar Cell's Front Electrode and Back Electrode

STUDY ON THE PROPERTIES OF p-type μc-SiC∶H THIN FILM AND APPLICATION ON SOLAR CELLS ON FLEXIBLE SUBSTRATE

Effects of annealing temperature and atmosphere on performances of Zn0.9Mg0.1O buffer layers for CIGS solar cell

Advancement in Treating Some Features of CIGS Thin Film Solar Cells During Manufacturing

Preparation and Characterization of Molybdenum Thin Films by Direct-Current Magnetron Sputtering

Development of Manufacturing CIGS Thin Film Solar Cells Deposited on Polyimide

Absorber layer improvement and performance analysis of CIGS thin-film solar cell

Improved Performance of Electroplated CZTS Thin-Film Solar Cells with Bifacial Configuration

Research and Characterization of an Absorber Layer Material-Cu(In,Ga)Se2 Sputtered on Polyimide Substrate in Material Engineering

Efficiency enhancement of copper indium gallium selenide solar cells fabricated on polyimide foils with multiple metal layers