Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Summary of research method of the low stress and no distortion welding technology of hull girder structure

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Controlling of Welding Residual Stress and Deflection Distortion for Flat Plate by Longitudinal Pre-stress Method

The Boom of the Welding Residual Stress Aging Treatment

Low Stress Welding Technology Without Post-Weld Heat Treatment

Research Progress on Welding Residual Stress and Deformation in Large or Complex Steel Structure

Reducing Distortion and Residual Stress Using Dynamically Controlled Low Stress No Distortion and Its Influence on Fatigue Crack Growth Properties of Steel Welded Joints

The Realization of Low Stress and Nonangular Distortion by Double-Sided Double Arc Welding

Controlling welding residual stress and distortion by a hybrid technology of transient thermal tensioning and trailing intensive cooling

Stress analysis and process technological scheme of on-site butt welding for extra long box structure

Experimental and Simulation Study on Welding Characteristics and Parameters of Gas Metal Arc Welding for Q345qD Thick-Plate Steel

EXPERIMENTAL STUDY OF WELDING RESIDUAL STRESS OF HIGH-STRENGTH SHIPBUILDING STEEL

Comparative Study of Welding Deformation of a Stiffened Panel under Various Welding Procedures

Experimental Research of Welding Residual Stress of Butt Welded Joint of Thick Steel Plate

Numerical Study on Welding Residual Stress Distribution of Corrugated Steel Webs

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Welding deformation prediction of hull structure based on Weld-sta software

Research of Complicated Ship Structure Welding Distortion Based on ANSYS

Optimization of welding parameters on welding distortion and stress in S690 high-strength steel thin-plate structures

Welding distortions of huge structures controlled accurately through the numerical method and model experiment

New Method to Control Residual Stresses and Distortion by Welding with Trailing Rotating Extrusion