Abstract:The thickness of steel plates used in the member has gradually increased to meet the load-bearing capacity requirements of long-span steel bridges. As the primary connection method of thick steel plate, welding will result in considerable welding residual stress with complex distribution. Large welding residual stress will significantly impact the performance of steel bridges. In this paper, the distribution of residual stress in welded thick steel plate is systematically studied, a specimen with a thickness of 80 mm was designed and fabricated, and the welding residual stress was measured by X-ray diffraction. The finite element model was established and verified by test results. Subsequently, the finite element calculation of the welding residual stress of steel plates with thicknesses of 20, 40, 60, 80, and 100 mm was carried out, and the distribution of surface residual stress and the influence of plate thickness on residual surface stress were studied; then the spatial evolution mechanism of welding residual stress was studied, and the distribution of residual stress inside steel plate and the influence of plate thickness on the distribution of residual stress were revealed. The results show that the surface and internal residual stresses of 20–100 mm thick plates have good symmetry on the paths perpendicular to the weld seam, and asymmetry only occurs in the weld seam and heat-affected zone where the stress fluctuates. On the paths perpendicular to the weld seam, the stress in the X direction transitions from the "M" shape distribution on the surface to the "Π" shape distribution inside for 20–40 mm thick plates, and the residual stress near the weld seam gradually changes from compressive to tensile; The distribution of stress in the X direction in the 80–100 mm thick plate has experienced the transition from "M" shape to "Π" shape to "M" shape, and the stress near the weld seam has experienced the transition from compressive to tensile to compressive. The stress change in the X direction of the 60 mm thick plate is between the above two cases. On the path of internal stress along the thickness, the maximum stress in the X direction is 310–400 MPa for 20–40 mm thick plates, which appears at about 1/2 plate thickness. The maximum stress in the X direction for 60–100 mm thick plates is 400–480 MPa, which appears at 0.2–0.3 times the thickness of the plate from the upper surface. The results could serve as a reference for welding residual stress analysis and guide optimization design of steel bridges made of thick steel plate.

Research Progress on Welding Residual Stress and Deformation in Large or Complex Steel Structure

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Numerical Application Research on the Welding Residual Stress of a Super-tall Giant Transfer Truss

Experimental research and numerical analysis of welding residual stress of butt welded joint of thick steel plate

Experimental Research of Welding Residual Stress of Butt Welded Joint of Thick Steel Plate

Finite element simulation of welding process and real-time monitoring assessment

A review of welding simulation methods for large components

Application and Research of Construction Mechanics and New Control Technology in Large and Complex Steel Structures Construction

Numerical Study on Welding Residual Stress Distribution of Corrugated Steel Webs

Research Status of Weldability of Advanced Steel

Research Of Weld On Axial Buckling Stress Of Multilayer Combined Cylindrical Shells

Numerical and experimental study on thermal-metallurgical-mechanical behavior of high-strength steel welded joint

Numerical simulation of residual stress and deformation on laser welding of "grooved-coat" structure

Experimental Investigation and Modeling on Residual Stress of Welded Steel Circular Tubes

Three-dimensional finite element analysis on welding residual stresses of construction steel

Residual Stress Of High Strength Steel Welded Sections

A Numerical Simulation of the Seismic Performance and Residual Stress of Welded Joints in Building Steel Structures Based on the Finite Element Method

Review on finite element analysis of welding deformation and residual stress

Experimental and Simulation Study on Welding Characteristics and Parameters of Gas Metal Arc Welding for Q345qD Thick-Plate Steel

Progress In Application And Research Of High Strength Steel Structures

Welding distortions of huge structures controlled accurately through the numerical method and model experiment