Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Qualitative Physical Modeling and Experimental Study on Forging Method with Horizontal V-Shaped Anvil

Study on Rational Width ratio of Anvil and Reduction in FM Forging Process

Research on Grain Refinement and Homogenization During the Mandrel Stretching Process of a Hollow Steel Ingot Used for Heavy Hydro-Generator Shaft

The Effect of the Forging Process on the Microstructure and Mechanical Properties of a New Low-Cost Ti-5Al-1.5Mo-1.8Fe Alloy

Research on Rotatory Deformation Uniformity and Compaction Effect of Super-heavy Hollow Steel Ingot

The microstructure, texture evolution and plasticity anisotropy of 30SiMn2MoVA high strength alloy steel tube processed by cold radial forging

Investigation on hollow steel ingot forging process of heavy cylinder forging

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

The effects of hot forging on the preform additive manufactured 316 stainless steel parts

A novel high-dynamic actuator based in-situ micro-forging process for wire arc additive manufacturing of aluminum alloy

Markedly enhancing mechanical properties of powder metallurgy superalloy by hot oscillatory forging

Influence of Forging Temperature on the Microstructures and Mechanical Properties of a Multi-Directionally Forged Al–Cu–Li Alloy

Numerical simulation and experiment study on hot extrusion process of 18Ni (250) maraging steel large fan shaft for aero-engines

3D FE modeling simulation of the double-roll hot rotary forging of large diameter thin-walled metal disk

Modeling and Numerical Simulation Research on Hollow Steel Ingot Forging Process of Heavy Cylinder Forging

Predictive Modeling and Optimization of Hot Forging Parameters for AISI 1045 Ball Joints Using Taguchi Methodology and Finite Element Analysis

Deformation Characteristic and Microstructure Evolution of Gh4169 Alloy Induced by Axial Upsetting and Axial Rotary Forging

Staggered Anvil and Rotation Processes for Refining and Homogenizing Centimeter-Scale Grains During Fm Forging of Superheavy Ingots

Numerical Simulation Research on Final Forging Process of 700MW Class Heavy Hydro-generator Shaft

Investigation of FM heavy forging process by the Moiré method Part III: A direct forging process standard

Modeling research on FM forging process of heavy low-pressure turbine rotor