Abstract:Ni-based supperalloys are widely applied in manufacturing of compressor and turbine discs and polycrystal turbine blades in the hot section of aero-engines, since they possessed excellent mechanical strength and creep resistance at high temperatures. Generally, hot working is an effective way for shaping metals and alloys. Lots of typical metallurgical behaviors occurred, which were related to the hot working parameters, including deformation temperature, strain rate and strain. And BP-ANN ( artificial neural network based on the error-back propagation) as well as Arrhenius types models were the two of most acknowledged constitutive models to determine the relationship between the flow behavior and hot deformation parameters of various metals and alloys, at present. In order to investigate the relationship between deformation parameters and flow stress behavior, and precisely simulate the flow behavior during hot deformation processes of GH4720Li alloy, the hot compressive tests of GH4720Li alloy were conducted at the deformation temperature range of 1060 similar to 1140 degrees C and strain rate range of 0.001 similar to 1 s(-1) on Gleeble 3500D thermal simulation testing machine in this work. The relationship between microstructure and hot deformation conditions was identified. The influence of hot processing parameters on flow stress behavior was analyzed. The temperature sensitivity of the flow stress decreased with increasing temperature at a strain rate of 0.1 s(-1.) The peak stress increased 23 MPa when the deformation temperature decreased from 1100 degrees C to 1080 degrees C, only increased 7 MPa when decreased from 1140 degrees C to 1120 degrees C. In addition, the Arrhenius model as well as BP artificial neural network model was established according to the true stress-strain curves. It shows that the established BP artificial neural network model can well exhibit the flow stress behavior of GH4720Li alloy compared with the Arrhenius model during hot deformation. The correlation coefficient between experimental findings and predicted flow stress determined by ANN model and Arrhenius model is 0.998 and 0.949, respectively. In addition, the dynamic recrystallization mechanism of the studied alloy was identified according to the deformed microstructure. Microstructure observation of the samples deformed at 1140 degrees C indicated that the discontinuous dynamic recrystallization was the main nucleation mechanism and newly grain nuclei distributed along the deformed grain boundaries. The dynamic recrystallization grain size of GH4720Li alloy decreases with the increase of strain rate when the samples deformed at 1140 degrees C and a strain of 0.8.

Deformation Characteristic and Microstructure Evolution of Gh4169 Alloy Induced by Axial Upsetting and Axial Rotary Forging

Study on the hot deformation behavior and microstructure evolution of as-forged GH3625 alloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Microstructure and mechanical property evolution mechanisms of 15Cr14Co12Mo5Ni2WA aviation gear steel during cold rotary forging

Spinning Process of 2219 Aluminum Alloy Tubes for Used in Hydroforming

Effect of Inter-Pass Annealing on the Deformation Microstructure of Ti-48Al-2Cr-2Nb Alloy

Effect of Multidirectional Forging on the Microstructures and Mechanical Properties of the Al–Mg–Si Alloy

Effect of Deformation Degree on Microstructure and Properties of Ni-Based Alloy Forgings

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Thermal deformation behavior and microstructure evolution of GH141 superalloy during double-cone gradient compression

Microstructural Evolution and Mechanical Behavior during Isothermal Multiaxial Forging of Nickel-Based Superalloy SUPERNI 718

Microstructure Evolution and Deformation Mechanism of AZ80 Alloy During Die Forging

Microstructural evolution and dynamic recrystallization mechanism of a heavily-alloyed Ni-based superalloy during hot extrusion

Effects of Multiaxial Forging on Microstructure and High Temperature Mechanical Properties of Powder Metallurgy Ti-45Al-7Nb-0.3W Alloy

Dynamic Softening Behavior and Microstructure Evolution of Nickel Base Superalloy

Microstructure Characterization of Reversed Transformation in Cryogenically Rolled 22MnB5

Numerical simulation and experiment study on hot extrusion process of 18Ni (250) maraging steel large fan shaft for aero-engines

Characterization of Residual Stresses and Grain Structure in Hot Forging of GH4169

Microstructural evolutions and mechanical properties of 6082 aluminum alloy part produced by a solution-forging integrated process

Microstructure Evolution of Different Forging Processes for 12%cr Steel During Hot Deformation

Study of Microstructure and Mechanical Properties by Torsional Behavior in Axial Closed Die Rolling Forming