Abstract:Integral passives are becoming increasingly important in realizing next generation electronics industry needs through gradual replacement of discretes. The need for integral passives emerges from the increasing consumer demand for product miniaturization thus requiring components to be smaller and packaging to be space efficient. In this paper, the feasibility of integration of polymer/ceramic thin film (∼5 μm thick) capacitors (C) with other passive components such as resistors (R) and inductors (L) has been discussed. An integrated RC network requiring relatively large capacitance and resistance is selected as a model for co-integration of R and C components using low temperature PWB compatible fabrication processes. This test vehicle is a subset of a large electrical circuit of a functional medical device. In order to produce higher capacitance density and reduce in-plane device area, multi-layer (currently two-layer) capacitors are stacked in the thickness direction. A commercially available Ohmega-Ply resistor/conductor material is selected for integral resistors. Resistors were fabricated using a multi-step lithography process with the utilization of two separate masks. Bottom copper electrodes for capacitors were also defined during the resistor fabrication process. Photodefinable epoxies filled with a high permittivity ceramic powder were used for fabrication of thin film capacitors. Epoxy and ceramic powders were mixed in the required proportion and blended using a high shear apparatus. The coating solution was homogenized in a roll miller for 3 to 5 days prior to casting in order to prevent settling of the higher density ceramic particles. Capacitors were fabricated by spin-coating on the sub-etched copper electrodes. The deposited dielectric layers were dried, exposed with UV radiation, patterned, and thermally cured. Top capacitor electrodes (copper) were deposited using a metal or an e-beam evaporator. The electrodes were patterned using the standard photolithography processes. Selected good samples were used for depositing the second capacitor layer. The RC network is extended to incorporate electroplated polymer/ferrite core micro-inductors through the fabrication of an industry prototype low pass RLC filter. Meniscus coating was evaluated for large area manufacturing with high process yield. A capacitance density of ∼3 nF cm−2 was obtained on a single layer capacitor with ∼6 μm thick films. The capacitance density was increased to ∼6 nF cm−2 with the two-layer deposition process. The capacitors were relatively stable up to a frequency range of 120 Hz to 100 KHz. Meniscus coating was qualified to be a viable manufacturable method for depositing polymer/ceramic capacitors on large area (300mm x 300mm) PWB substrates. Dielectric constant values in the range of 3.5 to 35 with increase in filler loading up to 45 vol% were achieved in the epoxy nanocomposite system where the dielectric constant of the host polymer was limited to ∼3.5. Higher dielectric constant polymers are required to meet the increasingly higher capacitance needs for the next generation electronics packaging. Possible avenues for achieving higher capacitance density in polymer/ceramic nanocomposite system have been discussed.

Using Embedded Capacitance to Improve Electrical Performance and Reduce Board Size

EMBEDDED CERAMIC CAPACITORS: THE ROAD TO RELIABILITY

Capacitance Extraction of Three-Dimensional Interconnects Using Element-By-Element Finite Element Method (Ebe-Fem) and Preconditioned Conjugate Gradient (pcg) Technique

Board power bus decoupling using embedded capacitance

The Influences of the Shaping Mould Design on the Performance of Capacitor and the Corresponding Countermeasure

In-package P/G Planes Analysis and Optimization Based on Transmission Matrix Method

Utilizing Flexible Printed Circuit Board (FPCB) to Realize Passives Integration in LLC Resonant Converter

Fan-Out Panel-Level PCB-Embedded SiC Power MOSFETs Packaging

Electrical Simulation Model to Improve Through-Silicon Capacitor(TSC) Capacitance

Influence of Solder on De-Embedded Capacitance

Analysis of Smt Decoupling Capacitor Placement in Electronic Packages Using Hybrid Modeling Method

Improving the electrical and mechanical performances of embedded capacitance materials by introducing tungsten disulfide nanoflakes into the dielectric layer

A High-Performance Micro Lithium-Ion Capacitor with 3D Interdigital Electrodes for On-Chip Energy Storage

Hybrid 3D Printing of Molten Metal Microdroplets and Polymers for Prototyping of Printed Circuit Boards Featuring Interdigitated 3D Capacitors

Fabrication and Characterization of Embedded Capacitors Based on Novel Nanocomposite As Dielectric Materials

Design and Simulation of Deep Trench Capacitor on High-Performance Silicon Interposer

Embedding of Passive and Active Components into FPC

Design and Process Implementation for Embedding Components

Fabrication and Characterization of Embedded Capacitors in PCB Using Epoxy/BaTiO3/PI Capacitor CCL

Next generation integral passives: materials, processes, and integration of resistors and capacitors on PWB substrates

Dielectric Quality of 3D Capacitor Embedded in Through-Silicon Via (TSV)