Abstract:Integral passives are becoming increasingly important in realizing next generation electronics industry needs through gradual replacement of discretes. The need for integral passives emerges from the increasing consumer demand for product miniaturization thus requiring components to be smaller and packaging to be space efficient. In this paper, the feasibility of integration of polymer/ceramic thin film (∼5 μm thick) capacitors (C) with other passive components such as resistors (R) and inductors (L) has been discussed. An integrated RC network requiring relatively large capacitance and resistance is selected as a model for co-integration of R and C components using low temperature PWB compatible fabrication processes. This test vehicle is a subset of a large electrical circuit of a functional medical device. In order to produce higher capacitance density and reduce in-plane device area, multi-layer (currently two-layer) capacitors are stacked in the thickness direction. A commercially available Ohmega-Ply resistor/conductor material is selected for integral resistors. Resistors were fabricated using a multi-step lithography process with the utilization of two separate masks. Bottom copper electrodes for capacitors were also defined during the resistor fabrication process. Photodefinable epoxies filled with a high permittivity ceramic powder were used for fabrication of thin film capacitors. Epoxy and ceramic powders were mixed in the required proportion and blended using a high shear apparatus. The coating solution was homogenized in a roll miller for 3 to 5 days prior to casting in order to prevent settling of the higher density ceramic particles. Capacitors were fabricated by spin-coating on the sub-etched copper electrodes. The deposited dielectric layers were dried, exposed with UV radiation, patterned, and thermally cured. Top capacitor electrodes (copper) were deposited using a metal or an e-beam evaporator. The electrodes were patterned using the standard photolithography processes. Selected good samples were used for depositing the second capacitor layer. The RC network is extended to incorporate electroplated polymer/ferrite core micro-inductors through the fabrication of an industry prototype low pass RLC filter. Meniscus coating was evaluated for large area manufacturing with high process yield. A capacitance density of ∼3 nF cm−2 was obtained on a single layer capacitor with ∼6 μm thick films. The capacitance density was increased to ∼6 nF cm−2 with the two-layer deposition process. The capacitors were relatively stable up to a frequency range of 120 Hz to 100 KHz. Meniscus coating was qualified to be a viable manufacturable method for depositing polymer/ceramic capacitors on large area (300mm x 300mm) PWB substrates. Dielectric constant values in the range of 3.5 to 35 with increase in filler loading up to 45 vol% were achieved in the epoxy nanocomposite system where the dielectric constant of the host polymer was limited to ∼3.5. Higher dielectric constant polymers are required to meet the increasingly higher capacitance needs for the next generation electronics packaging. Possible avenues for achieving higher capacitance density in polymer/ceramic nanocomposite system have been discussed.

EMBEDDED CERAMIC CAPACITORS: THE ROAD TO RELIABILITY

Using Embedded Capacitance to Improve Electrical Performance and Reduce Board Size

Capacitance Extraction of Three-Dimensional Interconnects Using Element-By-Element Finite Element Method (Ebe-Fem) and Preconditioned Conjugate Gradient (pcg) Technique

Next generation integral passives: materials, processes, and integration of resistors and capacitors on PWB substrates

Fabrication and Characterization of Embedded Capacitors in PCB Using Epoxy/BaTiO3/PI Capacitor CCL

Embedding of Passive and Active Components into FPC

Preparation and Properties of Embedded Thick Film Multilayer Capacitor

A strategy to detect the effect of electrode defects on the electrical reliability in multilayer ceramic capacitors

Effect of bias potential and dimension on electrochemical migration of capacitors for implantable devices

Board power bus decoupling using embedded capacitance

Fabrication and Characterization of Embedded Capacitors Based on Novel Nanocomposite As Dielectric Materials

Progress and challenges of ceramics for supercapacitors

Environmental qualification testing and failure analysis of embedded resistors

Design and Process Implementation for Embedding Components

Low-sintering composite multilayer ceramic capacitors with X7R specification

Research on the Feasibility of Thin Film Capacitance Material with Double-side-etch Process

Study on two kinds of etching methods to processing embedded capacitor PCB and the comparison between them

Design Strategies of High-Performance Lead-Free Electroceramics for Energy Storage Applications

Thermal-Mechanical-Electrical Coupled Design of Multilayer Energy Storage Ceramic Capacitors

Chemically Integrated Nickel-Based Resistors on Printed Circuits and Its Resistance Precisely Controlled

Reliability Mechanisms of the Ultrathin-Layered BaTiO3-based BME MLCC