Abstract:To enhance the efficiency of cathode electron injection of organic light-emitting diode (OLEDs), we designed a new hybrid modified layer (HML) with the structure of Bphen: LiF/Al/MoO3, which was applied to ITO/NPB/Alq(3)/Al. The traditional material LiF is used for the electron injection layer of the reference device. The results show that using HBL at the interface between organic and cathode is very effective. We have measured the electroluminescence (EL) spectra of the device. The EL peak of the device is 534 nm, which indicates that it is from Alga. It can be seen that the structure design of the multilayer modified layer does not change the luminescence spectrum of the device. Bright green emission can be obtained from the optimized EL devices. Compared with traditional device based on LiF, the performance of the single unit with hybrid modification layer has better luminous properties and efficiency. Present research work shows that when the optimum parameter of the hybrid layer is Bphen LiF(5 nm; 6%)/Al(1nm)/MoO3(5 nm), the maximum current efficiency and the maximum power efficiency of the device are 4. 28 cd.A(-1) and 2. 19 lm.W-1, respectively, which are 25. 5% and 23. 7% higher than those of the reference device. Current-voltage characteristics demonstrate that the hybrid interfacial layer can promote electron injection, thus increasing the current efficiency and reduced their operating voltage slightly of OLED. We systematically analyze the improvement of device performance from two aspects. On the one hand, LiF can fill the electron trap of Bphen to enhance the current injection, moreover, HML can also block hole transport and reduce the hole current. On the other hand, based on charge balance factor theory, HML enhances the injection of electrons and increases the charge balance factor, which improves the balance of carriers in the device. The experimental results show that the cathode hybrid layer can improve the performance of the device.

Performances enhancement in OLEDs by inserting ultrathin trilayer in electron injection structure and using MoO3 as hole buffer layer.

Low Operating-Voltage and High Power-Efficiency OLED Employing MoO3-doped CuPc As Hole Injection Layer

Electroluminescence Performance Of Organic Light-Emitting Diode With Molybdenum Trioxide Inside Hole Transport Layer

Improved Performance with a Hybrid Cathodic Interfacial Layer in OLEDs

Performance Enhanced OLEDs Using a Li3N Doped Tris(8-Hydroxyquinoline) Aluminum(Alq3) Thin Film as Electron-Injecting and Transporting Layer

Performance Improvement of Organic Light Emitting Diode with Aluminum Oxide Buffer Layer for Anode Modification

Improving Efficiency of Organic Light-Emitting Devices by Optimizing the Lif Interlayer in the Hole Transport Layer

Improved Performances of Organic Light-Emitting Diodes with Metal Oxide As Anode Buffer

P-113: Novel Structure Organic Light-Emitting Diodes with High Performance

Efficiency Enhancement Utilizing A Hybrid Anode Buffer Layer in Organic Light-emitting Devices

Improving the Performance of Organic Light-Emitting Devices by Incorporating Non-Doped TCNQ As Electron Buffer Layer

Enhanced Performance by Inserting Ultrathin SiO2 Layer in Organic Light‐emitting Devices

Enhanced Brightness and Efficiency in Organic Light-Emitting Devices Using an Lif-Doped Electron-Injecting Layer with Aluminium Cathode

Efficient Single-Active-Layer Organic Light-Emitting Diodes With Fluoropolymer Buffer Layers

Enhanced Performance in Organic Light-Emitting Diode by Utilizing MoO3-doped C60 As Effective Hole Injection Layer

Peformance Enhancement Of Organic Light-Emitting Diodes Based On Different Hole Transport Layers

Enhanced Hole Injection and Improved Performance in Organic Light-Emitting Devices by Utilizing a Novel Composite Hole Injection Layer

Improving Performance Of Deep-Blue Oled By Inserting Ultra-Thin Lif Between Hole-Blocking And Electron-Transporting Layers

High-efficiency and Low Voltage Organic Light-Emitting Device with a Composite Hole Transport Layer

Multilayer Cathode for Organic Light-Emitting Devices

Improvement of OLED Properties with the AlN Insulated Layer