Abstract:Charge balance is one of the most important factors for realizing high performance OLEDs. In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer and the electron transporting layer and thereby controlling the charge carrier supplies in the device. Red OLEDs with improved performance were achieved. Charge balance is one of the most important factors for realizing high performance organic light emitting devices (OLEDs). In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer (HIL) as well as the electron transporting layer (ETL) and thereby controlling the charge carrier supplies in the device. First, we develop a p‐dopant material (PD02), with a lowest unoccupied molecular orbit (LUMO) of −4.63 eV, much shallower than that of the commercial material (PD01) of which the LUMO is −5.04 eV. Nevertheless, this enables us to modulate the supply of holes to the emissive layer through tuning doping concentration. We demonstrate that device performances are significantly improved by employing such a scheme. With a 23% molar doping of PD02, a bottom emission red OLED achieves an external quantum efficiency (EQE) of over 30%, an operating voltage of 3.4 V and a LT95 ~15,000 h at 10 mA/cm2, with a Digital Cinema Initiative P3 (DCI‐P3) chromaticity of CIE (X, Y) = (0.68, 0.32). Moreover, the efficiency roll‐off is suppressed up till ~3500 cd/m2, a desirable feature in display applications. The lateral conductivity of by using such HIL is also found to be much lower than that of PD01, resulting in reduced crosstalk among RGB pixels. Next, a new electron transporting material (ETM‐02) with a deep LUMO of −2.86 eV is also introduced to further optimize the charge balance. Although devices with ETM‐02 shows lower voltage and higher EQE, lifetime is compromised. In order to improve lifetime, additional fine tuning of the charge balance is essential. Finally, a second p‐dopant PD03 with a LUMO of −4.91 eV is added to the HIL to further extend the modulation flexibility in the hole injection. A double‐layer HIL consisting of 8 nm of HTM:16% PD02 and 2 nm of HTM:3% PD03, where the former is in contact with anode, is adopted in the device structure. The bottom emission deep red device achieve EQE over 30%, an operating voltage of 3.2 V and an improved LT95 ~13,000 h at 10 mA/cm2 with a BT.2020 range chromaticity of CIE (X, Y) = (0.701, 0.299). In the double HIL configuration, the introduction of PD03 provides one more parameter for tuning and therefore improves the overall device performances.

A step-wise bilayered hole-injection layer composed of vanadium oxide and PEDOT:PSS for simultaneously enhancing efficiency and stability of organic light-emitting diodes

Controllable and efficient hole-injection layers with molybdenum oxide units by solution-processed procedure for OLEDs

Solution Process Feasible Highly Efficient Organic Light Emitting Diode with Hybrid Metal Oxide Based Hole Injection/Transport Layer

Improved Hole Injection And Transport Of Organic Light-Emitting Devices With An Efficient P-Doped Hole-Injection Layer

Use of Hybrid PEDOT:PSS/Metal Sulfide Quantum Dots for a Hole Injection Layer in Highly Efficient Green Phosphorescent Organic Light-Emitting Diodes

Work function tunning of lithium-doped vanadium oxide for functioning as hole injection layer in organic light-emitting diodes

Synergistic effects of Li-doped NiO film prepared by low-temperature combustion as hole-injection layer for high performance OLED devices

Small Molecular Phosphorescent Organic Light-Emitting Diodes Using A Spin-Coated Hole Blocking Layer

Highly efficient hole injection/transport layer-free OLEDs based on self-assembled monolayer modified ITO by solution-process

Utilizing VO 2 as a Hole Injection Layer for Efficient Charge Injection in Quantum Dot Light-Emitting Diodes Enables High Device Performance

Charge balance in OLEDs: Optimization of hole injection layer using novel p‐dopants

TPE-diphenylamine derivatives as solution-processable hole injectors with better charge balance for organic light-emitting diodes

Superior Hole Injection Material PEGDT/TPF/PVDF with p-Doping Capability for Highly Efficient Solution-Processed Organic Light-Emitting Diode

The Optimization of Hole Injection Layer in Organic Light-Emitting Diodes

Solution-processed polymer bilayer heterostructures as hole-transport layers for high-performance opaque and semitransparent organic solar cells

Solution-Processed Self-Stratifying Layer with Controllable Dielectric Polarization for High-Luminance Organic Light-Emitting Diodes

P-113: Novel Structure Organic Light-Emitting Diodes with High Performance

Fine‐Tuning Conformation of PEDOT Chains Enables Simultaneously Enhanced Conductivity, Work Function, Transmittance, and Waterproofness in PEDOT:PSS Interlayer for Highly Efficient and Stable Organic Photovoltaics

Organic light-emitting devices with a 2-(4-biphenyl)-5-(4-butylphenyl)-1,3,4-oxadiazole layer between the α-naphtylphenyliphenyl diamine and 8-hydroxyquinoline aluminum

Self-Assembly Of Conducting Polymer Nanowires As Hole Injection Layer For Organic Light-Emitting Diodes Applications

Feasible Modification of PEDOT:PSS by Poly(4-styrenesulfonic Acid): a Universal Method to Double the Efficiencies for Solution-Processed Organic Light-Emitting Devices.