Abstract:Charge balance is one of the most important factors for realizing high performance OLEDs. In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer and the electron transporting layer and thereby controlling the charge carrier supplies in the device. Red OLEDs with improved performance were achieved. Charge balance is one of the most important factors for realizing high performance organic light emitting devices (OLEDs). In this work, we provide a novel strategy to improve the charge balance in OLEDs by optimizing the hole injection layer (HIL) as well as the electron transporting layer (ETL) and thereby controlling the charge carrier supplies in the device. First, we develop a p‐dopant material (PD02), with a lowest unoccupied molecular orbit (LUMO) of −4.63 eV, much shallower than that of the commercial material (PD01) of which the LUMO is −5.04 eV. Nevertheless, this enables us to modulate the supply of holes to the emissive layer through tuning doping concentration. We demonstrate that device performances are significantly improved by employing such a scheme. With a 23% molar doping of PD02, a bottom emission red OLED achieves an external quantum efficiency (EQE) of over 30%, an operating voltage of 3.4 V and a LT95 ~15,000 h at 10 mA/cm2, with a Digital Cinema Initiative P3 (DCI‐P3) chromaticity of CIE (X, Y) = (0.68, 0.32). Moreover, the efficiency roll‐off is suppressed up till ~3500 cd/m2, a desirable feature in display applications. The lateral conductivity of by using such HIL is also found to be much lower than that of PD01, resulting in reduced crosstalk among RGB pixels. Next, a new electron transporting material (ETM‐02) with a deep LUMO of −2.86 eV is also introduced to further optimize the charge balance. Although devices with ETM‐02 shows lower voltage and higher EQE, lifetime is compromised. In order to improve lifetime, additional fine tuning of the charge balance is essential. Finally, a second p‐dopant PD03 with a LUMO of −4.91 eV is added to the HIL to further extend the modulation flexibility in the hole injection. A double‐layer HIL consisting of 8 nm of HTM:16% PD02 and 2 nm of HTM:3% PD03, where the former is in contact with anode, is adopted in the device structure. The bottom emission deep red device achieve EQE over 30%, an operating voltage of 3.2 V and an improved LT95 ~13,000 h at 10 mA/cm2 with a BT.2020 range chromaticity of CIE (X, Y) = (0.701, 0.299). In the double HIL configuration, the introduction of PD03 provides one more parameter for tuning and therefore improves the overall device performances.

Highly efficient hole injection/transport layer-free OLEDs based on self-assembled monolayer modified ITO by solution-process

Efficient Hole Transport Layers With Widely Tunable Work Function For Deep Homo Level Organic Solar Cells

Solution Process Feasible Highly Efficient Organic Light Emitting Diode with Hybrid Metal Oxide Based Hole Injection/Transport Layer

Controllable and efficient hole-injection layers with molybdenum oxide units by solution-processed procedure for OLEDs

Modification of ITO with Composite Self-Assembled Monolayer Enables Hole Injection and Transport Layer-Free TADF-OLED with Preferable Performance

Highly Efficient Nondoped Green Organic Light-Emitting Diodes with Combination of High Photoluminescence and High Exciton Utilization

Improved Hole Injection And Transport Of Organic Light-Emitting Devices With An Efficient P-Doped Hole-Injection Layer

Employing ∼100% Excitons in OLEDs by Utilizing a Fluorescent Molecule with Hybridized Local and Charge‐Transfer Excited State

High‐Efficiency, Solution‐Processed, Multilayer Phosphorescent Organic Light‐Emitting Diodes with a Copper Thiocyanate Hole‐Injection/Hole‐Transport Layer

A step-wise bilayered hole-injection layer composed of vanadium oxide and PEDOT:PSS for simultaneously enhancing efficiency and stability of organic light-emitting diodes

Enhanced efficiency and stability of organic light-emitting diodes via binary self-assembled monolayers of aromatic and aliphatic compounds on indium tin oxide

P-113: Society for Information Display: Novel Structure Organic Light-emitting Diodes With High Performance

P-113: Novel Structure Organic Light-Emitting Diodes with High Performance

Single-crystalline hole-transporting layers for efficient and stable organic light-emitting devices

Efficient inverted organic light-emitting devices using a charge-generation unit as electron-injection layers

Charge balance in OLEDs: Optimization of hole injection layer using novel p‐dopants

TPE-diphenylamine derivatives as solution-processable hole injectors with better charge balance for organic light-emitting diodes

Highly Efficient Doping‐Free Thermally Activated Delayed Fluorescent Organic Light‐Emitting Diodes with an Ultrathin Quasi‐Host‐Guest Emission Layer

Synergistic effects of Li-doped NiO film prepared by low-temperature combustion as hole-injection layer for high performance OLED devices

Rational Design of Aggregation-Induced Emission Luminogen with Weak Electron Donor-Acceptor Interaction to Achieve Highly Efficient Undoped Bilayer OLEDs.

Highly Efficient Inverted Organic Light-Emitting Diodes Adopting a Self-Assembled Modification Layer