Abstract:This research aims at increasing the utilization of platinum-ruthenium alloy (Pt-Ru) catalysts and thus lowering the catalyst loading in anodes for methanol electrooxidation. The direct methanol fuel cell’s (DMFC) anodic catalysts, Pt-Ru/C, were prepared by chemical reduction with a reducing agent added in two kinds of solutions under different circumstances. The reducing agent was added in hot solution with the protection of inert gases or just air, and in cold solution with inert gases. The catalysts were treated at different temperatures. Their performance was tested by cyclic voltammetry and potentiostatic polarization by utilizing their inherent powder microelectrode in 0.5 mol/L CH3OH and 0.5 mol/LH2SO4 solution. The structures and micro-surface images of the catalysts were determined and observed by X-ray diffraction and transmission electron microscopy, respectively. The catalyst prepared in inert gases showed a better catalytic performance for methanol electrooxidation than that prepared in air. It resulted in a more homogeneous distribution of the Pt-Ru alloy in carbon. Its size is small, only about 4.5 nm. The catalytic performance is affected by the order of the reducing agent added. The performance of the catalyst prepared by adding the reductant at constant temperature of the solution is better than that prepared by adding it in the solution at 0°C and then heating it up to the reducing temperature. The structure of the catalyst was modified, and there was an increase in the conversion of ruthenium into the alloyed state and an increase in particle size with the ascension of heat treatment temperature. In addition, the stability of the catalyst was improved after heat treatment.

The Feasibility Study of Using Methane As the Fuel for the Proton Exchange Membrane Fuel Cells under the Ambient Temperature

Direct Alkaline Anion Exchange Membrane Fuel Cell to Converting Methane into Methanol

Study on Performance of Liquid-feed Direct Methanol Fuel Cell

Methane to Methanol Conversion Using Proton-Exchange Membrane Fuel Cells and PdAu/Antimony-Doped Tin Oxide Nanomaterials

Preparation and Influence of Performance of Anodic Catalysts for Direct Methanol Fuel Cell

Carbon Aerogel Supported Pt–Ru Catalysts for Using As the Anode of Direct Methanol Fuel Cells

Mesocarbon microbeads supported Pt-Ru catalysts for electrochemical oxidation of methanol

Methane-fueled SOFC with Traditional Nickel-Based Anode by Applying Ni/Al2O3 As a Dual-Functional Layer

Mechanistic insight into catalytic conversion of methane on a Sr2Fe1.5Mo0.5O6−δ perovskite anode: a combined EIS-DRT, DFT and TPSR investigation

Performance of a Direct Methanol Fuel Cell

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

Influence of preparation process of MEA with mesocarbon microbeads supported Pt–Ru catalysts on methanol electrooxidation

Fluorination-enabled Interface of PtNi Electrocatalysts for High-Performance High-Temperature Proton Exchange Membrane Fuel Cells

Experimental investigation on influences of methanol reformate impurities in performances of high temperature proton exchange membrane fuel cells

A Liquid–Vapor Two-Phase Model of Direct Methanol Fuel Cells With Platinum Group Metal-Free Cathode Catalyst

Mesoporous carbon supported PtRu as anode catalyst for direct methanol fuel cell: Polarization measurements and electrochemical impedance analysis of mass transport

CO-tolerance behaviors of proton exchange membrane fuel cell stacks with impure hydrogen fuel

Direct Dimethyl Ether Fuel Cells with Low Platinum-Group-metal Loading at Anode: Investigations of Operating Temperatures and Anode Pt/Ru Ratios

The influences of catalyst combination on the high temperature proton exchange membrane fuel cell

Direct methane protonic ceramic fuel cells with self-assembled Ni-Rh bimetallic catalyst

Synergic effect investigation of carbon monoxide and other compositions on the high temperature proton exchange membrane fuel cell